|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
02-15-2008, 07:35 PM | #1 |
Gone Wild
Join Date: Dec 2007
Location: lake county FL
Posts: 327
|
help please!!!!!!!!!!!!!!!!!!!!!!!
my K&N and jet kit just came in today. i took off the stock round type filter box and replaced it with the K&N then took the bowl off the bottom of carb and changed main jet. i went to fire it up and it will only give me about half trottle then boggs bad. i hit the choke and gave it gas and it runs like a bat out of h#ll. what gives? i tried adjusting fuel air and no go.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-15-2008, 07:40 PM | #2 |
Gone Wild
Join Date: Nov 2007
Posts: 469
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
seams like too mutch air not anuf gaz you need to get a set of drill bit to clean torch tip & a digital micrometer
mesure witch one you have & go slowly biger before you start mabee give us more details like witch model of cart ,jet , filter combo you are using |
02-15-2008, 08:00 PM | #3 |
Admin/Moderator
Join Date: Dec 2006
Location: Ohio
Posts: 18,047
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
When you changed the jet, did you clean the bowl, float and surrounding area?
Could have a piece of debris blocking the jet. Just a thought. |
Ron
PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
02-15-2008, 08:31 PM | #4 |
Gone Wild
Join Date: Dec 2007
Location: lake county FL
Posts: 327
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
i am using the g-16 jet kit for lifted carts on my g-14 which tom says works along with the K&N.. I went from having a perfectly good cart to a cart that will barely go with the pedal 1/4 way down..ill take the bowl back off and try cleaning it again..
|
02-15-2008, 08:44 PM | #5 |
Admin/Moderator
Join Date: Dec 2006
Location: Ohio
Posts: 18,047
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
One tiny piece of crap in the bowl can cause lots of problems. That setup should work.
|
Ron
PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
02-15-2008, 08:45 PM | #6 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
I trust Tom....Did you tell him it was a G-14 (your car is more simular to a G2/G9/G8, alittle differant than a G16. If all checks out with Tom for the correct parts....I would think the "plastic" intake manifold got "cracked" or the gasket between the manifold and cylinder head is bad. There are only 2 adjustments to thes carbs....pilot adjustment screw (Must have a very sharp point!) Turn in till "lightley seated" then back off 1 1/2 turns. Throttle stop screw.....(throttle shaft must close all the way!) turn the screw in till it touches the throttle shaft, then 1/4 turn more. I'd really like to know how this one turns out. Later Dave
|
02-15-2008, 09:52 PM | #7 |
Gone Wild
Join Date: Dec 2007
Location: lake county FL
Posts: 327
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
dave from what i hear tom is one of the best. i contacted him through here and he told me g16.. im with you i asked him if it was the same as g9. i never messed with the intake manifold unless some how when i was tring to take the snorkle off the carb it cracked without knowledge. there are 3 screws one that has a few holes in it with a blunt flat end when its pulled out (gas/air)? one with spring that goes into the carb and one with a spring that hits the arm on top by the throttle cable. i have no idea what im doing
|
02-15-2008, 11:27 PM | #8 |
Getting Wild
Join Date: Feb 2008
Posts: 103
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
i ordered the same stuff from cartpartsplus. I ordered the k&n filter and the power up spring. I also ordered the jet that says its for carts with bigger tires or whatever! Is that the same thing you got? Hope it all works out for you...keep us posted
|
02-16-2008, 12:25 PM | #9 | |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
Quote:
|
|
02-16-2008, 05:00 PM | #10 |
Gone Wild
Join Date: Dec 2007
Location: lake county FL
Posts: 327
|
Re: help please!!!!!!!!!!!!!!!!!!!!!!!
unfortunatly i dropped the pilot jet crew in a place where my hands wont reach. so as soon as i get it back i'll do exactly as you say.. thanks alot dave your help is always apprieciated!!!! i will repost as soon as get done..
also dave when i took off the stock jet there was i little metal ring around it that was not attached. i put it on the new jet is this right? thanks chris........ |