04-13-2011, 12:56 AM | #1 |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Presedent
Has anyone ever taken a C/C president and turned it into a series cart using the factory foot switches and wiring but put a new series controller in it with the OBC to charge it. If so please send me a schematic of it. I'm try to help a guy out and he started on it but need's help bad. He doesn't want to start from scratch either. He has already cut all the factory wiring out of it.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-13-2011, 08:35 AM | #2 |
Gone Wild
Join Date: Mar 2009
Location: South Texas
Posts: 2,391
|
Re: Presedent
You need a SERIES MOTOR, SERIES F&R CONTROL to start with along with a almost complete rewire job?
|
04-13-2011, 09:49 AM | #3 | |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: Presedent
Quote:
If they do it will make my job a lot easier. I've never done this type of cart before. We have it all striped down. |
|
04-13-2011, 01:52 PM | #4 |
Getting Wild
Join Date: Jan 2010
Posts: 90
|
Re: Presedent
go down on this page and you have precedent foot switch wiring
http://www.buggiesgonewild.com/elect...ontroller.html |
04-13-2011, 06:30 PM | #5 | |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: Presedent
Quote:
Does the stock cart run off of OHM's? MCOR signal to the controller is it OHMS? Do you happen to know which two wireswould be used on a regular serirs cart controller? |
|
04-13-2011, 08:50 PM | #6 |
Gone Wild
Join Date: Oct 2010
Location: Panama City, FL
Posts: 1,408
|
Re: Presedent
looks like a variable ohm out-putter to me
seriously though, hook your meter to the 2 outside posts. this will tell you the value of the pot. ie: 5k, 10k, etc. depending on what the controller wants to see (ie: 0-5k, 5k-0), dictates how it should be connected. (if its backwards, reverse the 2 outer pot wires.) -sj |
04-13-2011, 11:27 PM | #7 |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: Presedent
That is the same as his. Thanks,
He bought a controller for a club car that has 5-0 Ohm's. I was just wondering which two wires to use since I've never done this conversion before. Thanks for the info and I hope we have it running by Friday! sonicj, so don't use the Yellow wire for a 2 wire hookup...correct! |
04-14-2011, 02:03 AM | #8 | |
Gone Wild
Join Date: Oct 2010
Location: Panama City, FL
Posts: 1,408
|
Re: Presedent
Quote:
the pot acts as a voltage divider. + and - are on the outer 2 pins, the wiper output is on the center pin. if you feed the pot say 5V on the outer two pins, the wiper pin will show 0 to 5V, or 5V to 0V. if you hook it up and it outputs 0 to 5V and you want it to output 5V to 0V, just switch the outer two wires. make sense? -sj |
|
04-14-2011, 02:17 AM | #9 |
Gone Wild
Join Date: Oct 2010
Location: Panama City, FL
Posts: 1,408
|
Re: Presedent
well i'll be d*****! some controllers do use 2 wire resistive inputs..!
ok, so if the controller wants a 2 wire input, you'll either use purple + yellow, or yellow + white/black. one combo will give you 0 to 5K the other will give 5K to 0. holla! -sj |
04-14-2011, 08:07 AM | #10 |
Gone Wild
Join Date: Mar 2009
Location: South Texas
Posts: 2,391
|
Re: Presedent
If I'm not mistaken one of the three wires runs to the B minus ground on controller?
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Starting problems on my Presedent | Gas Club Car | |||
2005 presedent IQ cart Problem | Electric Club Car |