|
Gas Club Car Gas DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
06-06-2011, 04:05 PM | #1 |
Getting Wild
Join Date: May 2011
Posts: 109
|
Governor adjustment question
Ok I have searched and read a lot of threads but couldn't find a good answer. I found the mod for a pre 97 cart, but not for a 01. Also I would like to know if I can adjust the governor without removing the rev limiter. I don't need the cart to go super fast just a little faster then 12mph. Also I will not be the only one driving it so I don't want someone else to blow up the motor revving it too high.
Thanks |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-06-2011, 04:25 PM | #2 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,443
|
Re: Governor adjustment question
Governor and rev limit should be two different things, the rev limit is part of the ignition and cuts spark at X rpm. Some you can disable some not.
Most of the governor mods you adjust the pedal up to pull more, long as it still idles. Beyond that you stiffen up the spring, beyond that you usually remove them as high pressure wears the throttle cable faster and you are going near that fast anyway. |
06-06-2011, 10:28 PM | #3 | |
Gone Wild
Join Date: Aug 2009
Location: Eldon Missouri
Posts: 977
|
Re: Governor adjustment question
Quote:
Chris. |
|
06-07-2011, 06:28 PM | #4 |
Getting Wild
Join Date: May 2011
Posts: 109
|
Re: Governor adjustment question
Yeh that was a little helpful. I have searched and read the stickies but the only detailed info I saw was for adjusting the governor on the older model cart. I also understand that they are 2 different things. But I was wondering if I can make the cart faster by adjusting the gov. without hitting the stock rev limit. Can anyone provide me with a simple detailed solution? Should I just try the zip-tie trick on the spring?
|
06-07-2011, 07:40 PM | #5 |
Gone Wild
Join Date: Apr 2010
Location: West Tennessee
Posts: 1,269
|
Re: Governor adjustment question
I have seen small zip ties ran thru the little spring and it pulls the govenor quicker?
|
06-07-2011, 09:12 PM | #6 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,443
|
Re: Governor adjustment question
The stiky I found said to shorten the rod from the pedal to the box on a DS. I was doing a carryall and the cable from the box to the governor arm on the trans is adjustable at the box. So I adjusted it near all the way, this makes the cart take off with the pedal much higher than it was. Before you have to push it maybe 75% of the way down before the cart moved. So you adjust the rod or cable or whatever you find to take up the slack. If that is not enough you tighten the spring with zipties or shorten it, etc. Most carts all use the same deal, but yamaha have an adjuster on the spring CC does not you have to mod the spring. You just keep going until it hits the rev limit. In the sticky you can put in neutral buy turning the service collar on the back of the shifter, then hold the pedal to the floor and adjust until it hits the rev limit. The governor is active in neutral. Note if you make the spring not spring anymore by fixing its length, it will disable the governor. You want to pull the spring tighter to reach X speed by adjusting the cable or shortening the spring or use a stiffer spring on the governor arm. You can only take out so much slack on the pedal it must not open the throttle on the engine until after it starts. At that point you must work on the spring.
|
06-07-2011, 09:19 PM | #7 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,443
|
Re: Governor adjustment question
|
06-07-2011, 10:14 PM | #8 |
Gone Wild
Join Date: Feb 2010
Location: Crook County,Illinois
Posts: 153
|
Re: Governor adjustment question
I used the zip tie mod on my 87 cc and it gained a couple more mph. I also did it on my 2005 Precedent and that sucker flys. On my 2003 ds i'm just going to bypass the governor all together. Just make sure if you use the zip tie mod, once you get it set to where you want, throw a couple of zip ties on there.
|
06-08-2011, 06:18 AM | #9 |
Gone Wild
Join Date: Apr 2010
Location: West Tennessee
Posts: 1,269
|
Re: Governor adjustment question
My zip tie gets me in the rpm limiter @ 28 mph.
If you tighten the throttle cable at the black box to much your cart will not shut off. |
06-08-2011, 12:48 PM | #10 |
Getting Wild
Join Date: May 2011
Posts: 109
|
Re: Governor adjustment question
What?? 28 mph and thats just with the zip-tie mod? Holy crap. Did you just zip-tie the whole spring so that it doesn't stretch at all? So you don't recommend tightening the cable at the box? Just zip-tie the spring?
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Governor rod adjustment | Gas Club Car | |||
Governor adjustment | Gas EZGO | |||
governor adjustment | Gas Club Car | |||
Smell gas after governor adjustment | Gas EZGO | |||
Governor adjustment question | Gas EZGO |