|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
03-05-2020, 06:07 PM | #1 |
Gone Wild
Join Date: Oct 2019
Location: Houston, TX
Posts: 319
|
Curtis 1268-5403
I am getting a 2-4 error code. Let me say this is on an HDK. I had to install a whole new wiring harness. The cart turns on and runs but is in limp mode. Everything seems ok. Think the solenoid is bad? Could the controller be bad? It runs in forward and reverse and tow run switch is also functional.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-05-2020, 06:51 PM | #2 |
Gone Wild
Join Date: Oct 2019
Location: Houston, TX
Posts: 319
|
Re: Curtis 1268-5403
Another question, if there is a 48v 200 amp solenoid, can I replace it with any other golf cart solenoid of that spec? Can I put it a larger 250 amp or higher?
|
03-05-2020, 10:37 PM | #3 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Curtis 1268-5403
If it will drive more than a few inches, the solenoid is not gonna be your answer.
|
03-06-2020, 08:59 AM | #4 |
Gone Wild
Join Date: Oct 2019
Location: Houston, TX
Posts: 319
|
Re: Curtis 1268-5403
I keep getting all kinds of different codes. I am not sure what is going on.
|
03-06-2020, 11:23 AM | #5 |
Gone Wild
Join Date: Oct 2019
Location: Houston, TX
Posts: 319
|
Re: Curtis 1268-5403
Can I use a 1268-5504 500 amp controller in place of the 1268-5403? i looked at the pin outs, they are the same. It seems like I could give one a try. The reason I ask is there is one available locally that is in great shape for fairly decent price. I have seen several different controllers used in these carts.
|
03-06-2020, 10:26 PM | #6 |
Gone Wild
Join Date: Oct 2019
Location: Houston, TX
Posts: 319
|
Re: Curtis 1268-5403
FYI it does work... I need to have it programmed. But I am having that done tomorrow.
|
03-07-2020, 04:14 AM | #7 |
Gone Insane
Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
|
Re: Curtis 1268-5403
The VCL (Vehicle Control Language) is for a different motor and vehicle. VCLs cannot be reprogrammed very easy, it requires having the correct OS and VCL files from Curtis, and the Curtis software WinVCL to compile them to create a combined file. Something that Curtis never released to the public.
|
03-07-2020, 11:06 AM | #8 |
Gone Wild
Join Date: Oct 2019
Location: Houston, TX
Posts: 319
|
Re: Curtis 1268-5403
Bob,
I had spoken to a couple of service guys. We have the full programming pack from the manufacturer. Is there a reason that with the OEM programmer and manufacturer program that this can't work? The cart drives with the 5504 controller in it, limp mode though. I think the 5403 controller is bad. I am going to have to get a curtis controller programmed no matter what. This chinese cart is a pain in my a@$ but what can I do? |
03-07-2020, 03:51 PM | #9 | |
Gone Insane
Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
|
Re: Curtis 1268-5403
Quote:
|
|
03-07-2020, 06:37 PM | #10 |
Gone Wild
Join Date: Oct 2019
Location: Houston, TX
Posts: 319
|
Re: Curtis 1268-5403
Bob,
I have no clue about any of that. I don't know what to do but I have to find something for this cart. I have some files. Should I find another method? |
|
|
Similar Threads | ||||
Thread | Forum | |||
Fault (code) 1,3 Curtis 1268-5403 | Electric Club Car | |||
Curtis 1268-5403 stuck in low speed | Electric Club Car | |||
Curtis 1268-5403 | Electric golf carts | |||
Curtis controller mod. 1268-5403 | Golf Carts and Parts | |||
Looking for Curtis Controller 1268-5403 | Golf Carts and Parts |