|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
04-19-2020, 07:34 PM | #1 |
Not Yet Wild
Join Date: Mar 2020
Posts: 5
|
MPT800 (Series) nogo. Alltrax recommendation?
Good evening all.
I have what I think is a 2007 36V EZ-Go MPT 800 . The serial number search on the checker site gives me no results. I've gone through all the stickys for diagnostics and troubleshooting, cleaned the contacts, checked the batteries, jiggled wires and checked the contacts again... and I'm assuming that my Speed Controller (25864G09) is the problem. Can anyone recommend the model of ALLTRAX controller that I need to replace this thing? It's pushing a 73445G01 36-48v motor. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-19-2020, 08:35 PM | #2 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,173
|
Re: MPT800 (Series) nogo. Alltrax recommendation?
If you just want to replace what you have an Alltrax SR would work.. You sure yours is bad? Solenoid click ?
|
04-20-2020, 01:00 AM | #3 |
Not Yet Wild
Join Date: Mar 2020
Posts: 5
|
Re: MPT800 (Series) nogo. Alltrax recommendation?
Solenoid does click. I was hoping that the unit wasn't bad. I disassembled it and took a look for circuit board burn or any smell of something fried... no luck.
|
04-20-2020, 09:13 PM | #4 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,173
|
Re: MPT800 (Series) nogo. Alltrax recommendation?
Put your volt meter on b- and m- and check for voltage through the range of the go pedal. Should sweep through to pack voltage.
|
04-21-2020, 01:27 PM | #5 |
Not Yet Wild
Join Date: Mar 2020
Posts: 5
|
Re: MPT800 (Series) nogo. Alltrax recommendation?
When I Connect (-) probe to M- terminal.
Connect (+) probe to B+ terminal. The reading should indicate approx. 0 volts, mine is reading 0.56. Pedal start: 0.35 Pedal fully pressed 0.00. |
04-21-2020, 01:57 PM | #6 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: MPT800 (Series) nogo. Alltrax recommendation?
Quote:
A more definitive test is going from B- to M- since only the MOSFETs inside the controller are between those two points while going from M- to B+ includes just about everything in the high current circuit except the MOSFETs. (The voltage reading will be the opposite - Pack voltage when solenoid clicks and 0V when pedal is on floor) Connect the DVM negative lead to the controller's B- terminal and go looking for the missing voltage. The F/R switch is the most likely suspect. |
|
04-29-2020, 03:48 PM | #7 |
Not Yet Wild
Join Date: Mar 2020
Posts: 5
|
Re: MPT800 (Series) nogo. Alltrax recommendation?
Good call. Removed the F/R switch. One of the brass lugs has shorted on something. There was built up melted plastic, and no contact. Took it apart and cleaned it, adjusted the lug, got it working.
I also had to replace the PDS. Unsure what the issue was with my original, but once replaced, the cart is up again. Thank ya’ll for the tips. |
Tags |
alltrax, mpt, no go, solenoid click |
|
|
Similar Threads | ||||
Thread | Forum | |||
Alltrax series issue | Electric EZGO | |||
04 series club car DS controller recommendation | Electric Club Car | |||
97 TXT Series NOGO New Motor | Electric EZGO | |||
1995 mpt800 steering tie rod help.! | Electric EZGO | |||
2 Speeds on Series TXT with Alltrax | Electric EZGO |