Question about 1980 EZGO

RR24 · 06-29-2013, 02:53 PM

Hey folks I need a little help, how do you get the rubber trim that goes around the edges of the cart back on?

I took it off to do a little painting.

sonnym · 10-23-2013, 06:38 PM

Did you get new trim ?? If so where did you get it.. I have not tried to put it on ,Is it that bad??

salinasgoodoleboy · 10-23-2013, 09:43 PM

gotta put it on the lip closest to the steering wheel first then use a baby screwdriver to wedge the front over the other lip. If that makes any sense lol. Might not hurt to heat it with a heat gun a bit so make it easier to flex.

Sonnym- you can buy it by the roll from almost any cart parts store, its expensive though cause it only comes by the roll and theres enough to do 2 carts. I think last time i saw it it was like 160$ for a roll.

salinasgoodoleboy · 10-23-2013, 09:44 PM

by cart parts store I mean website....

redcloud · 10-25-2013, 09:12 PM

I read a thread some place on line were a guy put his into a pail of hot water to get good and warm so it was pliable.
I hate that you can not just buy a piece to do one cart.

06-29-2013, 02:53 PM	#1
RR24 Not Yet Wild Join Date: Apr 2013 Posts: 22	Question about 1980 EZGO Hey folks I need a little help, how do you get the rubber trim that goes around the edges of the cart back on? I took it off to do a little painting.
RR24 Not Yet Wild Join Date: Apr 2013 Posts: 22

10-23-2013, 06:38 PM	#2
sonnym Not Yet Wild Join Date: Nov 2012 Location: Cumming Ga. Posts: 12	Re: Question about 1980 EZGO Did you get new trim ?? If so where did you get it.. I have not tried to put it on ,Is it that bad??

10-23-2013, 09:43 PM	#3
salinasgoodoleboy Gone Wild Join Date: Jun 2013 Location: Salinas, Ca Posts: 178	Re: Question about 1980 EZGO gotta put it on the lip closest to the steering wheel first then use a baby screwdriver to wedge the front over the other lip. If that makes any sense lol. Might not hurt to heat it with a heat gun a bit so make it easier to flex. Sonnym- you can buy it by the roll from almost any cart parts store, its expensive though cause it only comes by the roll and theres enough to do 2 carts. I think last time i saw it it was like 160$ for a roll.

10-23-2013, 09:44 PM	#4
salinasgoodoleboy Gone Wild Join Date: Jun 2013 Location: Salinas, Ca Posts: 178	Re: Question about 1980 EZGO by cart parts store I mean website....

10-25-2013, 09:12 PM	#5
redcloud Gone Wild Join Date: May 2013 Posts: 320	Re: Question about 1980 EZGO I read a thread some place on line were a guy put his into a pail of hot water to get good and warm so it was pliable. I hate that you can not just buy a piece to do one cart.
redcloud Gone Wild Join Date: May 2013 Posts: 320

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
1980 electric ezgo	Electric EZGO
1980 g1 oil pump question	Gas Yamaha
1980 ezgo small wiring question	Electric EZGO
1980 ezgo backfires	Gas EZGO
1980 G1 carburetor question	Gas Yamaha