|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
05-31-2012, 10:06 PM
|
#1 |
|
Getting Wild
Join Date: Mar 2012
Location: TX
Posts: 117
|
New ST Cowl not lining up?
I ordered a new ST front cowl already painted and am having some trouble putting on my 97 TXT. The top lip doesn't have holes to attach to the dash, and the instructions say to use silicone. Also the front bracket that rivets to the nameplate is not even close to lining up. If I go ahead and put it on, it will be held only by the flares and the silicone across the top lip and will be flimsey. Am I over thinking this?
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
05-31-2012, 10:11 PM
|
#2 |
|
Getting Wild
Join Date: Mar 2012
Location: TX
Posts: 117
|
Re: New ST Cowl not lining up?
Also, I added that support under the cowl. It's from a ST, and I read that it was supposed to be used anytime you switch cowls.
|
|
|
|
|
06-02-2012, 10:11 AM
|
#3 |
|
Getting Wild
Join Date: Mar 2012
Location: TX
Posts: 117
|
Re: New ST Cowl not lining up?
Anyone out there?
|
|
|
|
|
06-02-2012, 11:37 AM
|
#4 |
|
Gone Wild
 Join Date: Aug 2011
Location: Tyler, Texas
Posts: 661
|
Re: New ST Cowl not lining up?
I don't know but I'm watching this thread because I just ordered the ST cowl for mine. Good luck and please post what you figure out.
|
|
|
|
|
06-02-2012, 05:25 PM
|
#5 |
|
Getting Wild
Join Date: Mar 2012
Location: TX
Posts: 117
|
Re: New ST Cowl not lining up?
I ordered the st brace # 71463-G01, to go with the bracket #
71101G02P that I already have put on. I think the brace sits on top of it, and supports the weight of the front end. I don't see how it will work correctly without it. |
|
|
|
|
06-07-2012, 09:07 AM
|
#6 |
|
Getting Wild
Join Date: Mar 2012
Location: TX
Posts: 117
|
Re: New ST Cowl not lining up?
I have the brace installed and really think that it is needed. I'll post pics when I get the cowl installed.
|
|
|
|
|
06-08-2012, 03:37 PM
|
#7 |
|
Getting Wild
Join Date: Mar 2012
Location: TX
Posts: 117
|
Re: New ST Cowl not lining up?
I got the cowl on with the ST Brackets in place. I had to put the brace on under the support, but at least the cowl in supported. If you order a St cowl, I would advise against the one like I got without the dash holes. Hope this helps someone.
|
|
|
|
|
06-08-2012, 03:46 PM
|
#8 |
|
Gone Wild
Join Date: Aug 2011
Location: Tyler, Texas
Posts: 661
|
Thanks for the post. I'm about ready to mount mine but mine has the dash holes for rivets.
|
|
|
|
|
06-08-2012, 09:49 PM
|
#9 |
|
Getting Wild
Join Date: Mar 2012
Location: TX
Posts: 117
|
Re: New ST Cowl not lining up?
Here's the cowl installed.
|
|
|
|
|
06-08-2012, 10:00 PM
|
#10 |
|
Gone Wild
Join Date: Aug 2011
Location: Tyler, Texas
Posts: 661
|
That looks great! What lights did you use? I hate to spend $200 for a light kit for mine.
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Air intake questions on lining... | Gas EZGO | |||
| Lining up rear springs to spring plate | Lifted Golf Carts | |||
| Truck Bed Lining/Rhino Lining | Body and Paint | |||
| lining up clutches for engine swap | Gas EZGO | |||
| G9 Cowl / plastic swap. Which Cowl do I buy? | Gas Yamaha | |||
Linear Mode
