|
Gas Club Car Gas DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
08-24-2010, 12:48 PM | #1 |
Not Yet Wild
Join Date: Aug 2010
Posts: 4
|
1990 Club car With flat head Rev limiter question and govenor question
I have a 1990 Club car with a flat head I just ordered the clutch spring power kit and Im wondering if there is a way to get rid of the rev limiter and what should I do with the govenor
Thanks for the help Guys |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-24-2010, 08:30 PM | #2 |
Not Yet Wild
Join Date: Aug 2010
Posts: 4
|
Re: 1990 Club car With flat head Rev limiter question and govenor question
I read the stickys and did some searching I just could not find much on the flat head and I dont see a rev limiter box any were,just a coil!
|
08-24-2010, 11:24 PM | #3 |
Not Yet Wild
Join Date: Jul 2009
Location: Northwest Washington
Posts: 67
|
Re: 1990 Club car With flat head Rev limiter question and govenor question
Sounds like you are trying to do every thing you can to blow that motor, that 20 year old flathead aint built for speed and high rpm's. But if thats what you want to do its your buggy, just my .02. The governor is the rev limiter. Big Block might be in your future.
Good luck |
08-26-2010, 06:35 PM | #4 | |
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: 1990 Club car With flat head Rev limiter question and govenor question
Quote:
i have to add i agree............................................8 ) |
|
08-26-2010, 11:43 PM | #5 |
Gone Wild
Join Date: Aug 2009
Location: Eldon Missouri
Posts: 977
|
Re: 1990 Club car With flat head Rev limiter question and govenor question
|
08-27-2010, 01:31 AM | #6 |
Not Yet Wild
Join Date: Aug 2010
Posts: 4
|
Re: 1990 Club car With flat head Rev limiter question and govenor question
Ok got cha Well the govenor is already unhooked at the carb can you guys tell me how it should be adjusted then I can hook it back up,I talked to a guy that said it has to be hooked up and you could bend it to get the results you wanted.
Thanks for the help |
08-27-2010, 11:14 AM | #7 |
Not Yet Wild
Join Date: Jul 2009
Location: Northwest Washington
Posts: 67
|
Re: 1990 Club car With flat head Rev limiter question and govenor question
When Gov Arm is at rest it should be parallel with the rear axel.
"Gov Rod" Straight end goes in Gov Arm, 90 deg bend end goes in Throttle Plate Pivot Lever. Should be a plastic bushing in Throttle Plate and spring clip to hold rod in Throttle Plate Loosen Rod bolt at Gov Arm Push Throttle wide open and hold there. Pull Gov Arm towards the Carb till it stops and hold there "It dosen't move very far" Tighten bolt at Gov Arm. Good Luck |
08-27-2010, 08:17 PM | #8 |
Not Yet Wild
Join Date: Aug 2010
Posts: 4
|
Re: 1990 Club car With flat head Rev limiter question and govenor question
Thanks a ton,so what engine swap if any would you guys say to use.
|
08-27-2010, 10:30 PM | #9 |
Not Yet Wild
Join Date: Jul 2009
Location: Northwest Washington
Posts: 67
|
Re: 1990 Club car With flat head Rev limiter question and govenor question
Tough question, I hear good and bad about any and all of them. If I had to choose I would do the Vanguard.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Flat head valve lash?? | Gas Club Car | |||
Flat head bore size? | Gas Club Car | |||
Newbie question on flat tire - 86 Marathon | Gas EZGO | |||
G1 govenor question | Gas Yamaha | |||
What!?! Another govenor question!?! | Gas Club Car |