|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
02-23-2016, 03:07 PM | #1 |
Getting Wild
Join Date: Jun 2015
Posts: 109
|
Multi-Step Potentiometer versus MCOR1
Hello,
Hoping to get some help on this. I'm helping a friend rebuild a Club Car DS 48 volt, I believe 1997. It has a multi-step potentiometer, and black plastic half moon shaped item in between the batteries. I have an extra FSIP 500 AMP controller that came off my 2001 48 volt club car, which I believe is a MCOR1. It has a small black plastic box on the right side of the frame rail attached to the pedal assembly. 1. Can we use this 500 amp controller on this older multi-step potentiometer? 2. What's the difference between the 5-0 and 0-5 ohms requirement? 3. If this will work, will the stock 2.75HP motor be okay with the 500 amp controller? Only until he can upgrade to a new motor. I have not only the controller, but heavy duty solenoid, and #4 cables as well, so if this will work we can do this on a budget. Thanks! |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-23-2016, 03:26 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: Multi-Step Potentiometer versus MCOR1
Good news - The 97 and 01 carts both use the same 5k-0 throttle signal so the control will work with the multistep in the 97 .
You can use the 500 amp control with the stock motor. The driver will decide if the motor lasts a long time or a short time. Slow operation, big tires, heavy loads, deep footing & hard starts all make the motor consume additional amperage. Not all the amperage going to the motor is converted into power, some is converted into heat. So keep an eye on the motor, you should be able to hold your hand on it at any time. |
02-23-2016, 03:33 PM | #3 | |
Getting Wild
Join Date: Jun 2015
Posts: 109
|
Re: Multi-Step Potentiometer versus MCOR1
Quote:
What about the motor, will it be okay with the 500 amp controller until he can afford a new motor? Thanks, Rob |
|
02-23-2016, 03:34 PM | #4 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: Multi-Step Potentiometer versus MCOR1
The answer is yes, hidden in my first response.
|
02-23-2016, 03:42 PM | #5 |
Getting Wild
Join Date: Jun 2015
Posts: 109
|
Re: Multi-Step Potentiometer versus MCOR1
|
02-23-2016, 03:45 PM | #6 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: Multi-Step Potentiometer versus MCOR1
No problem, Sounds like a good project. Have fun!
|
02-23-2016, 05:39 PM | #7 |
Getting Wild
Join Date: Jun 2015
Posts: 109
|
Re: Multi-Step Potentiometer versus MCOR1
|
02-23-2016, 06:20 PM | #8 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: Multi-Step Potentiometer versus MCOR1
It does help the heat to transfer from the controller to the sink and that's a good thing. It can potentially extend the life of the controller.
|
02-23-2016, 06:42 PM | #9 |
Getting Wild
Join Date: Jun 2015
Posts: 109
|
Re: Multi-Step Potentiometer versus MCOR1
|
02-23-2016, 06:45 PM | #10 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: Multi-Step Potentiometer versus MCOR1
It's still going to transfer heat without it but tin foil hat guys will go so far as to mill both surfaces to insure 100% contact and apply the heat compound. You know 95% of all controls go in with nothing...
|
Tags |
controller upgrade |
|
|
Similar Threads | ||||
Thread | Forum | |||
Multi-step Potentiometer for 95 CC | Electric Club Car | |||
Multi-Step Pot rebuild? | Electric Club Car | |||
97 club car multi-step potentiometer | Electric Club Car | |||
Multi-step pot. test | Electric Club Car | |||
Multi Step Resistors | Electric Club Car |