04-21-2020, 11:26 AM | #21 |
Gone Wild
Join Date: Aug 2010
Location: Central Florida
Posts: 1,506
|
Re: Official Duromax 440 Swap Thread
Yes they ship very quick. I am in florida so it usually always here next day unless its small order and they ship Usps. Did you see my message about the crankshaft. NR Racing has 5 of the 69mm stroker crankshafts sitting on their shelf if you wanted to make yours a 460 before u put it in the cart!
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-22-2020, 07:40 PM | #22 |
Gone Wild
Join Date: Dec 2019
Posts: 193
|
Re: Official Duromax 440 Swap Thread
Can anyone confirm that the Duromax pushrods are 6.5 before I order?
Sent from my iPhone using Tapatalk |
04-22-2020, 07:49 PM | #23 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,644
|
Re: Official Duromax 440 Swap Thread
They should be. That is the standard clone length.
|
04-22-2020, 07:50 PM | #24 |
Gone Wild
Join Date: Dec 2019
Posts: 193
|
Re: Official Duromax 440 Swap Thread
|
04-22-2020, 07:53 PM | #25 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,644
|
Re: Official Duromax 440 Swap Thread
The 6.5" are used on the stud mounted rocker arms and the 6.74" are for shaft mounted rockers. 2 Other notes 1) The HD valve springs 2) retainer that use valve lash caps on both intake and exhaust valves. That lash cap set up is on the VC 460 but some of the other clones it is not.
|
04-23-2020, 08:34 AM | #26 | |
Gone Wild
Join Date: Dec 2019
Posts: 193
|
Re: Official Duromax 440 Swap Thread
Quote:
Thank you Ill take a look at it when it gets here. Sent from my iPhone using Tapatalk |
|
04-23-2020, 08:35 AM | #27 |
Gone Wild
Join Date: Dec 2019
Posts: 193
|
Re: Official Duromax 440 Swap Thread
Im planning on getting a 1.25 U bend to come off the head of the motor. After that would it be ok to run 1.5 pipe? The pipe bender I have access to only goes down to 1.5 pipe.
Sent from my iPhone using Tapatalk |
04-23-2020, 08:49 AM | #28 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,644
|
Re: Official Duromax 440 Swap Thread
Most of the muffler inlets are 1.5 " so you should be good.
|
04-23-2020, 09:16 AM | #29 |
Gone Wild
Join Date: Aug 2010
Location: Central Florida
Posts: 1,506
|
Re: Official Duromax 440 Swap Thread
I used 1-1/4 stainless PIPE. Bought pre bent pieces on eBay and welded it together. Muffler inlet was 1-1/2 so I got a short piece of 1-1/2 TUBING with 1-1/4 Id and cut a 1 or 1-1/2 piece to make a adapter for the pipe to seal into the muffler and welded it up. Worked out very good.
|
04-23-2020, 09:17 AM | #30 |
Gone Wild
Join Date: Aug 2010
Location: Central Florida
Posts: 1,506
|
Re: Official Duromax 440 Swap Thread
Remember: PIPE is measured off the ID, TUBING goes off OD!
|
|
|
Similar Threads | ||||
Thread | Forum | |||
The officially official Cougar Scooter build thread | Members Rides | |||
My Official 1986 Rebuild Thread answer all my questions. | Gas EZGO | |||
The official Cougar Scooter build thread | Restoration | |||
My Official '97 CC DS Build Thread | Electric Club Car |