|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
03-25-2017, 07:11 PM | #1 |
Not Yet Wild
Join Date: Mar 2017
Posts: 50
|
EZGO tie rods wobble on lift spacers
Just lifted my 2000 EZGO TXT with the budget 4" block lift kit and after playing with the front - trying to align it straight for a few hours - I couldn't figure out why it would never stay aligned perfectly until I noticed that the tie rod ends with the grease nipple were not tight on the lift's tie rod block.
There is about 1/8" of play all around due to the castle nut not having any more thread to climb up and properly tighten the tie rod. The mini castle nut on the tie rod literally runs out of thread and becomes tight on the tie rod before it actually tightens the tie rod end bolt to the lift's tie rod block. Any ideas on the best way to fix this? I was thinking of some washers to be used as spacers to make up for the extra room but is that too shoddy? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-25-2017, 09:12 PM | #2 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: EZGO tie rods wobble on lift spacers
Might be, might not be. Depends on how much slack needs to be taken to get the tapered tie rod ends to fit tight. One thick washer is OK, in my opinion (only on the side with the castle nut). A stack of washers, not so good.
|
03-25-2017, 11:16 PM | #3 |
Not Yet Wild
Join Date: Mar 2017
Posts: 50
|
Re: EZGO tie rods wobble on lift spacers
For now I'm using some galvanized washers they are pretty thick. Almost ~2mm in height. One side needed one washer and one side needed two.
Not so bad I guess? |
03-26-2017, 11:17 AM | #4 |
Wild Gone
Join Date: Oct 2016
Location: Davie, FL
Posts: 633
|
Re: EZGO tie rods wobble on lift spacers
I had the same issue and resolved the same way. I actually stripped the castle nut before I realized what was going on. I had to replace my tie rod end and nut.
Sent from my SCH-I545 using Tapatalk |
03-26-2017, 07:23 PM | #5 |
Not Yet Wild
Join Date: Mar 2017
Posts: 50
|
Re: EZGO tie rods wobble on lift spacers
|
03-30-2017, 08:46 AM | #6 |
Not Yet Wild
Join Date: Mar 2017
Posts: 50
|
Re: EZGO tie rods wobble on lift spacers
I had a late night thought on this.
There was a revision to the 'economy' 4" lift kit recently and the directions it came with do not reflect the change. The old kit looks like this, with FOUR U-shaped risers for the front tie rods/shocks: The new lift kits have only TWO U-shaped risers and now include TWO O-shaped risers as shown here (I know this photo is of a different pre-1994 kit but the new O-shaped risers are included in the post-1994 kits, now): The directions are not clear which are for the shocks and which are for the tie rods as the photos on the printed paper included have both as the U-shaped versions. Does anyone know which is which for the new kit? The O-shaped risers are thicker so it seems like they were having either a bending issue (shocks) or a tie rod issue as I stated in the OP but I'm not sure which is which. |
03-31-2017, 08:35 AM | #7 |
Not Yet Wild
Join Date: Mar 2017
Posts: 50
|
Re: EZGO tie rods wobble on lift spacers
Anyone installed one recently?
|
04-05-2017, 09:08 AM | #8 |
Not Yet Wild
Join Date: Feb 2017
Location: Z hills
Posts: 9
|
Re: EZGO tie rods wobble on lift spacers
I did I had to cut the closed loop brackets to make mine work. My instructions were vague to say the least. I used the cut ones/ thicker on the tie rods.
|
04-05-2017, 09:14 AM | #9 | |
Not Yet Wild
Join Date: Mar 2017
Posts: 50
|
Re: EZGO tie rods wobble on lift spacers
Quote:
It's working out much better now with no play in the steering with one washer on each side. I didn't have to do any cutting but I did tighten the bolt holding it on so that the bracket is angled - so that it doesnt hit anything when at full turn. |
|
04-05-2017, 09:45 AM | #10 |
Not Yet Wild
Join Date: Feb 2017
Location: Z hills
Posts: 9
|
Re: EZGO tie rods wobble on lift spacers
Good deal. What size tires are you going to run?
|
|
|
Similar Threads | ||||
Thread | Forum | |||
wtb wheel spacers and tie rods 98 ezgo txt | Golf Carts and Parts | |||
EZGO PDS 6-Inch Drop-Axle Lift Biggest Tires/Spacers? | Lifted Golf Carts | |||
wheel spacers-centered wheels-3in. lift ezgo | Lifted Golf Carts | |||
6" jakes lift w/spindles/tie rods/ coil over shocks $225 | Golf Carts and Parts | |||
97' Ezgo txt 23" tires rubbing the brake arm with 5" Drop Axle Lift..Spacers Needed? | Lifted Golf Carts |