|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
02-09-2012, 08:37 PM | #1 |
Getting Wild
Join Date: Dec 2011
Posts: 99
|
88 2 cycle ezgo exhaust bolts
i have lost the bolts that attach the exhaust pipe to the motor. the pipe starts at the motor and ends at the muffler. everthing is okay but the bolts have fill out. i need to know what size bolts i need. it looks like there are 2.
hot rod |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-10-2012, 02:01 AM | #2 |
Not Yet Wild
Join Date: Dec 2011
Location: Nokomis, FL
Posts: 63
|
Re: 88 2 cycle ezgo exhaust bolts
hot rod: the book says that they should be studs not bolts.
"stud exhaust port MB X 1.25/ 5/16+-18 UNC 2A" and "nut, hex, 5/8-18"hope this helps.. you can take this info to the hardware store (Lowe's /home-depot/ace) they should get you the right stud or bolt if you want to use bolts.. |
02-10-2012, 10:18 AM | #3 |
Getting Wild
Join Date: Dec 2011
Posts: 99
|
Re: 88 2 cycle ezgo exhaust bolts
thanks walt-rate you are right they are studs so mbx1.25/ 5/16+-18 unc 2a is the right stud for this. or is it 5/8-18" stud. how long is the stud?
|
02-10-2012, 11:09 AM | #4 |
Not Yet Wild
Join Date: Dec 2011
Location: Nokomis, FL
Posts: 63
|
Re: 88 2 cycle ezgo exhaust bolts
If I 'm right the 5/16-18 is the stud, and the 5/8-18
is the nut side. if you use bolts I think the can only get 1.5" not the 1.25".. If you use the 1.5" bolt just add some washers on the out side. make sure you use locktite "blue" |
02-12-2012, 11:13 AM | #5 |
Not Yet Wild
Join Date: Oct 2011
Location: JC MO.
Posts: 11
|
Re: 88 2 cycle ezgo exhaust bolts
The nut will be the same size as the stud.
Yes, it's 5/16 x 18 stud and nut. the wrench size is 1/2" the two studs are 1.250 long. |
02-13-2012, 08:46 AM | #6 |
Gone Wild
Join Date: Feb 2011
Posts: 1,515
|
Re: 88 2 cycle ezgo exhaust bolts
Hot Rod just stand by I'm going to solve your problem today as I have a 85 2pg apart now and I'm going to get the studs today.I checked the bolts that were in the exh with a standard nut and they are metric so don't force a 5/16X18 stud in there I'll post after finding the correct studs. I'm not saying yours may be standard but just try to install a 5/16 course bolt by hand not wrench if it goes easy OK if not it's metric. Stay tuned!!!
|
02-13-2012, 10:48 AM | #7 |
Gone Wild
Join Date: Feb 2011
Posts: 1,515
|
Re: 88 2 cycle ezgo exhaust bolts
Mystery solved The stud size is 8mmX1.25 and the length is1 1/4 long be sure to pickup some nuts while you there. Put a bit of blue loctite on the studs when installing then jum the stud with 2 nuts and secure in the cyl. When installing the pipe loosely fit it and start the nut with the least amount clearance pushing the pipe up as you go then install the other nut. (LOCK WASHERS RECOMMENDED) and your good to go. Hope it helps
|
02-13-2012, 08:04 PM | #8 |
Getting Wild
Join Date: Dec 2011
Posts: 99
|
Re: 88 2 cycle ezgo exhaust bolts
thanks to all who gave me advice it was 8m and 1 inch 1/2 long with washer and lock nut and i used loctite. running good will check in a couple days to make sure all is tight thanks again.
hot rod |
01-26-2013, 08:43 PM | #9 |
Not Yet Wild
Join Date: Jan 2013
Location: West Banks of Kentucky Lake
Posts: 27
|
Re: 88 2 cycle ezgo exhaust bolts
Found it!!
|
|
|
Similar Threads | ||||
Thread | Forum | |||
88 EZGO exhaust | Gas EZGO | |||
Need Exhaust Manifold 98 EZGO | Gas EZGO | |||
Exhaust bolts/studs for a 83 EZGO? | Gas golf carts | |||
88 ezgo 2 cycle gas/oil mix coming out of exhaust | Gas EZGO | |||
295 ezgo exhaust | Golf Carts and Parts |