|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
12-24-2015, 10:32 AM | #1 |
Crazy Wild
Join Date: Jun 2015
Location: Carolina Lowcountry
Posts: 796
|
V Glide Full Throttle Postion
Here's a pic of my v glide at full throttle. The wiper arm is in between to top plate and the one next to it. Should it be contacting just the top plate?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-24-2015, 11:47 AM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: V Glide Full Throttle Postion
Yes
|
12-24-2015, 10:02 PM | #3 |
Crazy Wild
Join Date: Jun 2015
Location: Carolina Lowcountry
Posts: 796
|
Re: V Glide Full Throttle Postion
Thank you. I'll adjust wiper to top plate only.
Merry Christmas. Muddog |
12-24-2015, 11:56 PM | #4 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: V Glide Full Throttle Postion
If you don't adjust it, almost all the current will flow only through the portion of the wiper pad that is touching that last Vglide pad.
|
12-28-2015, 01:36 PM | #5 |
Crazy Wild
Join Date: Jun 2015
Location: Carolina Lowcountry
Posts: 796
|
Re: V Glide Full Throttle Postion
The reason I opened the v glide was the cart keeps going after the pedal is released. I figured the problem was in the v glide, so I took it apart cleaned ,adjusted and put it back together.
Didn't solve problem. Cart still wants to go when pedal is released. It barely creeps, like at low speed. What is my next step ? Thanks,Muddog |
12-28-2015, 01:42 PM | #6 |
Old Sky Soldier
Join Date: Dec 2011
Location: Kentucky
Posts: 3,881
|
Re: V Glide Full Throttle Postion
Did you do anything with the micro switch in the v glide.
|
12-28-2015, 01:47 PM | #7 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: V Glide Full Throttle Postion
The only 2 failure possibilities are:
Make sure the solenoid coil (small posts) only have +36v when the pedal is pressed. If that is the case, replace the solenoid as the main contacts are welded. If the solenoid coil has +36v the entire time and the V-Glide wiper arm is pressing the micro-switch, replace the micro-switch. |
12-28-2015, 01:52 PM | #8 |
Crazy Wild
Join Date: Jun 2015
Location: Carolina Lowcountry
Posts: 796
|
Re: V Glide Full Throttle Postion
Checked mirco switch. Throttle up: no continuity Throttle down: continuity.
I have constant 36v across top solenoid lugs at all times. Muddog |
12-28-2015, 03:57 PM | #9 | |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: V Glide Full Throttle Postion
Quote:
Or did You measure from each big post to pack negative? If the big post connected to the V-Glide has +36v with the pedal UP, the solenoid contacts are welded and it needs to be replaced. |
|
12-28-2015, 04:14 PM | #10 |
Crazy Wild
Join Date: Jun 2015
Location: Carolina Lowcountry
Posts: 796
|
Re: V Glide Full Throttle Postion
Measured across posts. 36v constant.
Replaced solenoid. Haven't tested yet. Trying to adjust throttle, can't get rod loose from pedal Does the throttle rod just pop off the ball ? Thanks, Muddog |
|
|
Similar Threads | ||||
Thread | Forum | |||
Yamaha G1 Only Runs with full choke and full Throttle | Gas Yamaha | |||
yamaha g2 bogs at half throttle through full throttle | Gas Yamaha | |||
Full throttle acceleration weak, 1/2 throttle okay..? | Electric EZGO | |||
Key postion when charging | Electric Club Car | |||
Full throttle, Half throttle????? | Electric EZGO |