|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
05-17-2020, 01:41 PM | #11 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: EZGO PDS Motor not running
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-20-2020, 01:28 AM | #12 |
Not Yet Wild
Join Date: Apr 2013
Location: Louisiana
Posts: 42
|
Re: EZGO PDS Motor not running
Does open armature mean the motor is bad?
|
05-20-2020, 02:43 AM | #13 |
Not Yet Wild
Join Date: Apr 2013
Location: Louisiana
Posts: 42
|
Re: EZGO PDS Motor not running
I retested motor continuity and got the same results. I also checked
A1-Motor Body OL A2-Motor Body OL F1-Motor Body OL F2-Motor BOdy OL I checked the controller. With Key on - Initial reading is 27 V as I pressed the accelerator pedal the voltage increased to 37 and then dropped back to 27 |
05-20-2020, 11:55 AM | #14 |
Not Yet Wild
Join Date: Apr 2013
Location: Louisiana
Posts: 42
|
Re: EZGO PDS Motor not running
I had read something that a resistor needed to be removed from the controller before testing. If so, this is something I did not do.
|
05-20-2020, 01:53 PM | #15 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: EZGO PDS Motor not running
|
05-20-2020, 04:42 PM | #16 |
Not Yet Wild
Join Date: Apr 2013
Location: Louisiana
Posts: 42
|
Re: EZGO PDS Motor not running
checked the controller.
With Key on - Initial reading is 27 V as I pressed the accelerator pedal the voltage increased to 37 and then dropped back to 27 Could the controller cause the motor to "Appear" bad when I checked the continuity? |
06-01-2020, 08:51 AM | #17 |
Not Yet Wild
Join Date: Apr 2013
Location: Louisiana
Posts: 42
|
Re: EZGO PDS Motor not running
Got my new motor and the controller is arriving today. I have read that the wires should be run together in pairs to the motor. Should I run A1 - F1 together or A1-A2 together?
|
06-01-2020, 08:53 AM | #18 |
Not Yet Wild
Join Date: Apr 2013
Location: Louisiana
Posts: 42
|
Re: EZGO PDS Motor not running
Got my new motor and the controller is arriving today. I have read that the wires should be run together in pairs to the motor. Should I run A1 - F1 together or A1-A2 together?
|
06-01-2020, 12:33 PM | #19 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: EZGO PDS Motor not running
I bundled the A1, A2, F1, F2 and speed sensor cable together with Ty-wraps and Ty-wrapped the bundle to the frame, leaving a plenty of slack at the motor end since the motor moves forward and backwards quite a bit during acceleration and braking.
|
06-01-2020, 03:31 PM | #20 |
Not Yet Wild
Join Date: Apr 2013
Location: Louisiana
Posts: 42
|
Re: EZGO PDS Motor not running
Thanks,
I'm looking forward to getting back up and running |
Tags |
ezgo pds motor |
|
|
Similar Threads | ||||
Thread | Forum | |||
2005 EZGO TXT motor not running and running jerky | Electric EZGO | |||
Non running plum quick gunslinger 2 series Ezgo motor. | Golf Carts and Parts | |||
2010 EZGO not running/running very slowly | Electric EZGO | |||
2005 Electric EzGo wont go but motor sounds like it is running? | Electric EZGO | |||
new motor now not running | Electric Club Car |