|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
06-11-2020, 05:12 PM | #1 |
Not Yet Wild
Join Date: Jun 2020
Location: Burleson, Texas
Posts: 9
|
09 RXV tries to move but wont
I've got a 2009 RXV that tries to move but wont. New brake, new input shaft bearing, motor is extremely clean inside and doesn't smell burnt, 50V at the solenoid, ran great then all of the sudden just wouldn't do anything. Brake is releasing. Its not a Curtis controller so I cant hook up to it with my diagnostic reader. I'm starting to think encoder??? Any help would be greatly appreciated.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-11-2020, 07:37 PM | #2 |
Not Yet Wild
Join Date: May 2020
Posts: 9
|
Re: 09 RXV tries to move but wont
I was having the same problem with my 2008, couldn’t figure out what it was for a while. Ended up being the electrical connection under the cup holder. Was a little loose and cart would not move. Tighten up that connection and it runs great. Long shot but it was what was causing mine to have the same issue.
|
06-11-2020, 08:52 PM | #3 |
Gone Wild
Join Date: Aug 2012
Location: Houma, Louisiana
Posts: 950
|
Re: 09 RXV tries to move but wont
I had a similar issue with a 2009 a while back. I was able to release the parking brake using the fuses. Would not release in neutral with the run/tow switch in tow. Ended up being my solenoid.
|
06-11-2020, 09:35 PM | #4 |
Not Yet Wild
Join Date: Jun 2020
Location: Burleson, Texas
Posts: 9
|
Re: 09 RXV tries to move but wont
I bypassed that already
|
06-12-2020, 08:40 AM | #5 | |
Not Yet Wild
Join Date: Jun 2020
Location: Burleson, Texas
Posts: 9
|
Re: 09 RXV tries to move but wont
Quote:
|
|
06-12-2020, 10:16 AM | #6 |
Gone Insane
Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
|
Re: 09 RXV tries to move but wont
If you bypass the solenoid, the cart will not operate! The controller is a computer that monitors everything. If even one of over a dozen conditions are not met, it will not pass the POST, Power On Self Test. Be VERY careful messing with wiring on an RXV, as it is very easy to damage or corrupt the controller!
|
06-12-2020, 10:19 AM | #7 |
Not Yet Wild
Join Date: Jun 2020
Location: Burleson, Texas
Posts: 9
|
Re: 09 RXV tries to move but wont
Bob thanks for the reply. I did not bypass the solenoid only the plug under the cup holder. Simply cut and spliced the wires bypassing the plug.
|
06-12-2020, 10:52 AM | #8 |
Gone Insane
Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
|
Re: 09 RXV tries to move but wont
Not a good idea, as that is the programming port on Danaher RXVs. Cannot run diagnostics without it. I carry an FSIP Danaher handset with me for helping members with Danaher controlled RXVs
|
06-12-2020, 10:59 AM | #9 |
Not Yet Wild
Join Date: Jun 2020
Location: Burleson, Texas
Posts: 9
|
Re: 09 RXV tries to move but wont
Worked in a pinch to eliminate that being the issue.
|
06-12-2020, 12:14 PM | #10 |
Gone Insane
Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
|
Re: 09 RXV tries to move but wont
|
Tags |
ezgo, rxv, wont move |
|
|
Similar Threads | ||||
Thread | Forum | |||
Wont stop beeping and wont move | Electric EZGO | |||
96 club car ds solenoid wont click and cart wont move unless you jump solenoid | Electric Club Car | |||
Ezgo dcs solenoid clicks but wont disengage and wont move | Electric EZGO | |||
DS wont move...... | Electric Club Car |