08-19-2018, 09:02 PM | #1 |
Not Yet Wild
Join Date: Aug 2018
Location: Corpus Christi Texas
Posts: 30
|
Driven Clutch
I have a 1999 CC with FE290. One of my driven clutch slides is gone. Appears to me the screw broke off flush with the clutch. Any ideas how to remove screw?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-20-2018, 04:30 AM | #2 |
Photoshop Guy
Join Date: Aug 2012
Location: Canal Fulton, OH
Posts: 3,845
|
Re: Driven Clutch
The main screw that holds the clutch to the input shaft? You'll probably need an easy-out.
|
08-20-2018, 06:18 AM | #3 |
Not Yet Wild
Join Date: Aug 2018
Location: Corpus Christi Texas
Posts: 30
|
Re: Driven Clutch
Not the main screw that holds the clutch. The little screw that holds one of the three clutch slides.
|
08-20-2018, 09:13 AM | #4 |
Bonafide Nincompoop
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 8,987
|
Re: Driven Clutch
Only thing to do is drill it out. Before you do that check for play between the clutch shaft and the sliding sheave. If you can feel the sheave rock back and forth on the shaft you just need to replace the whole clutch. Too much wear there will lead to the clutch rattling and will cause rough opening/closing of the sheave.
|
08-20-2018, 04:46 PM | #5 |
Not Yet Wild
Join Date: Aug 2018
Location: Corpus Christi Texas
Posts: 30
|
Re: Driven Clutch
Fairtax4me
Thanks for update. Do I hold the Sheave in one hand then attempt to rock the outer part? There for trying to find play between the outter and inner |
08-20-2018, 07:17 PM | #6 |
Bonafide Nincompoop
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 8,987
|
Re: Driven Clutch
Yeah, hold the outer section, and try to wiggle the sliding sheave on the shaft. A tiny amount of movement is acceptable, but if you can see it rock around it's time to replace it.
|
08-21-2018, 08:22 AM | #7 |
Not Yet Wild
Join Date: Aug 2018
Location: Corpus Christi Texas
Posts: 30
|
Re: Driven Clutch
The shack rattle and roll passed. Thanks you for your input.
|
08-21-2018, 09:13 AM | #8 |
Bonafide Nincompoop
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 8,987
|
Re: Driven Clutch
Then you should be good to drill it out! Might need a helicoil insert to get good threads in there.
Be sure to put a little blue loctite on the threads of those little screws. If they back out at all and the slide comes loose it will break off. |
08-22-2018, 02:58 PM | #9 |
Getting Wild
Join Date: Jan 2018
Posts: 88
|
Re: Driven Clutch
Contact a Snap-On tool truck driver and get a couple reverse cut (left rotation) drill bits. You might luck out and have it catch and back itself out.
I think the smallest -MIGHT- be 1/16". A -little- heat while your drilling might help the broken screw to come out. |
|
|
Similar Threads | ||||
Thread | Forum | |||
Club car performance clutch and driven clutch | Golf Carts and Parts | |||
Drive Clutch or Driven Clutch | Gas EZGO | |||
Shimming a driven driven clutch | Gas EZGO | |||
Dive Clutch and Driven Clutch. Is this right?? | Gas EZGO |