1984 G1 not running

murrman26 · 10-08-2018, 04:50 PM

Is that ohms or voltage

Sent from my VS990 using Tapatalk

1984G1 · 10-08-2018, 07:02 PM

When I test the orange wire directly at the motor with a voltmeter I am getting 0. I checked the black wire going into the motor harness to make sure it was grounded and it was. With the voltmeter hooked to the positive side of the battery I had a 12.33 reading. Engaged the pedal motor turns and it dropped down to 0 until I let off the pedal. Is this a charge coil issue? If so how tough are they to change? And where can you get one? From what I have been reading I would say one of the connections on it have probably came loose inside the motor.

And sorry I just seen your reply because I didn’t click I’ve dto the next page. That is voltage. I’m new to using an ohms meter so if I had it set correctly. When I check the orange wire coming from the CDI it reads 1.6.

murrman26 · 10-09-2018, 06:15 AM

I'm getting like 20 volts off of charge coil when pedal is engaged

Sent from my VS990 using Tapatalk

1984G1 · 10-09-2018, 06:24 AM

So sounds like I’m in need of a charge coil?

murrman26 · 10-09-2018, 06:25 AM

Make sure battery has a good charge pull the brown wire off of the CDI box ground your test meter and hook it to the brown wire going to the motor and crank it over and see what your voltage is

Sent from my VS990 using Tapatalk

1984G1 · 10-09-2018, 11:33 AM

Do I need to ground directly to the battery or do I need to ground somewhere else?

murrman26 · 10-09-2018, 11:34 AM

Battery is fine

Sent from my VS990 using Tapatalk

1984G1 · 10-09-2018, 01:13 PM

Okay I tried that last night and wasn’t getting anything. Even tried it at the harness down by the motor to see if maybe there was an issues with the wire from motor to CDI. Still no reading.

murrman26 · 10-09-2018, 01:15 PM

Sounds like you may have a bad Exciter coil do you have to pull the cover off the motor and pull your flywheel off and then you can see it had to do that to mine and wasn't hard at all you need a harmonic balancer puller set

Sent from my VS990 using Tapatalk

murrman26 · 10-09-2018, 01:20 PM

Here's mine

Sent from my VS990 using Tapatalk

10-08-2018, 04:50 PM	#11
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18	Re: 1984 G1 not running Is that ohms or voltage Sent from my VS990 using Tapatalk
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18

10-08-2018, 07:02 PM	#12
1984G1 Not Yet Wild Join Date: Oct 2018 Posts: 13	Re: 1984 G1 not running When I test the orange wire directly at the motor with a voltmeter I am getting 0. I checked the black wire going into the motor harness to make sure it was grounded and it was. With the voltmeter hooked to the positive side of the battery I had a 12.33 reading. Engaged the pedal motor turns and it dropped down to 0 until I let off the pedal. Is this a charge coil issue? If so how tough are they to change? And where can you get one? From what I have been reading I would say one of the connections on it have probably came loose inside the motor. And sorry I just seen your reply because I didn’t click I’ve dto the next page. That is voltage. I’m new to using an ohms meter so if I had it set correctly. When I check the orange wire coming from the CDI it reads 1.6.
1984G1 Not Yet Wild Join Date: Oct 2018 Posts: 13

10-09-2018, 06:15 AM	#13
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18	Re: 1984 G1 not running I'm getting like 20 volts off of charge coil when pedal is engaged Sent from my VS990 using Tapatalk
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18

10-09-2018, 06:24 AM	#14
1984G1 Not Yet Wild Join Date: Oct 2018 Posts: 13	Re: 1984 G1 not running So sounds like I’m in need of a charge coil?
1984G1 Not Yet Wild Join Date: Oct 2018 Posts: 13

10-09-2018, 06:25 AM	#15
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18	Re: 1984 G1 not running Make sure battery has a good charge pull the brown wire off of the CDI box ground your test meter and hook it to the brown wire going to the motor and crank it over and see what your voltage is Sent from my VS990 using Tapatalk
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

10-09-2018, 11:33 AM	#16
1984G1 Not Yet Wild Join Date: Oct 2018 Posts: 13	Re: 1984 G1 not running Do I need to ground directly to the battery or do I need to ground somewhere else?
1984G1 Not Yet Wild Join Date: Oct 2018 Posts: 13

10-09-2018, 11:34 AM	#17
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18	Re: 1984 G1 not running Battery is fine Sent from my VS990 using Tapatalk
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18

10-09-2018, 01:13 PM	#18
1984G1 Not Yet Wild Join Date: Oct 2018 Posts: 13	Re: 1984 G1 not running Okay I tried that last night and wasn’t getting anything. Even tried it at the harness down by the motor to see if maybe there was an issues with the wire from motor to CDI. Still no reading.
1984G1 Not Yet Wild Join Date: Oct 2018 Posts: 13

10-09-2018, 01:15 PM	#19
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18	Re: 1984 G1 not running Sounds like you may have a bad Exciter coil do you have to pull the cover off the motor and pull your flywheel off and then you can see it had to do that to mine and wasn't hard at all you need a harmonic balancer puller set Sent from my VS990 using Tapatalk
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18

10-09-2018, 01:20 PM	#20
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18	Re: 1984 G1 not running Here's mine Sent from my VS990 using Tapatalk
murrman26 Not Yet Wild Join Date: Sep 2018 Posts: 18

Similar Threads
Thread	Forum
2005 EZGO TXT motor not running and running jerky	Electric EZGO
Getting 1984 Running	Gas EZGO
2010 EZGO not running/running very slowly	Electric EZGO
1984 ezgo 2pg running problem	Gas EZGO
1984 2 stroke running rough	Gas EZGO