|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
05-19-2015, 04:57 PM | #1 |
Gone Wild
Join Date: Jan 2010
Location: LA (Lower Alabama)
Posts: 276
|
Modified EZ Go won't go
OK, Here is what I have...
97 Ez Go Switched to series (Plumb Quick Torque Motor) 700A Logisystems controller 8, 6V T106 Cart is wired to where solenoid clicks with key, not pedal. (My electrical Engineer buddy did... forgot his reasoning) Recently replaced solenoid, don't think that is the issue. Got back from a ride, ate dinner, got back on and nothing. I have a voltage gauge from ScottyB showing pack voltage of 51.1V I am a gas engine guy with a voltage meter looking for dumb-down help on how and what to test. I will attach picks of my frankenstein. The cart has ran perfect for about five years (minus the recent replacement of the solenoid) THANKS IN ADVANCE!!!! Attached Thumbnails |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-19-2015, 04:59 PM | #2 |
Gone Wild
Join Date: Jan 2010
Location: LA (Lower Alabama)
Posts: 276
|
Re: Modified EZ Go won't go
Controller readings with Neg of Meter to pack neg.
Top pin: 51 Volts Second pin: 14.1 volts Third pin: .5 volts |
05-19-2015, 05:00 PM | #3 |
Gone Wild
Join Date: Jan 2010
Location: LA (Lower Alabama)
Posts: 276
|
Re: Modified EZ Go won't go
also tested solenoid, working correctly
Between second and third pin: voltage at 13.6 and drops to 12.2 when pedal fully depressed. |
05-19-2015, 05:03 PM | #4 |
Gone Wild
Join Date: Jan 2010
Location: LA (Lower Alabama)
Posts: 276
|
Re: Modified EZ Go won't go
With black on pack neg, white stays 14 volts
pressing pedal with black on pack neg, black ranges from .4-1.7 volts Voltage between B- and M- is pack voltage. This doesn't change when pedal depressed. |
05-19-2015, 05:11 PM | #5 | |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: Modified EZ Go won't go
Quote:
Seems your throttle signal is way to low. |
|
05-19-2015, 05:21 PM | #6 |
Gone Wild
Join Date: Jan 2010
Location: LA (Lower Alabama)
Posts: 276
|
Re: Modified EZ Go won't go
This?
"Between second and third pin: voltage at 13.6 and drops to 12.2 when pedal fully depressed." |
05-19-2015, 05:24 PM | #7 |
Gone Wild
Join Date: Jan 2010
Location: LA (Lower Alabama)
Posts: 276
|
Re: Modified EZ Go won't go
I am not sure which way I tested it is correct. Between the two pins or from pack neg to each individual pin??
|
05-20-2015, 04:51 AM | #8 |
Gone Wild
Join Date: Jan 2010
Location: LA (Lower Alabama)
Posts: 276
|
Re: Modified EZ Go won't go
bump
|
05-20-2015, 09:18 AM | #9 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Modified EZ Go won't go
I don't know what the throttle voltages for a Logitech controller should be, but it appears that Logitech is copying the Curtis ITS scheme.
You have a steady 14V on the white wire and the black with varies from 0.4V with pedal up to 1.7V with pedal down. The voltage on black wire varies with pedal movement, so the ITS sensor, in and of itself, is working. Since the voltage source for the ITS sensor is the controller and the interpretation of the throttle signal is done by the controller, it appears that the controller is bad. |
05-20-2015, 10:04 AM | #10 |
Gone Wild
Join Date: Jan 2010
Location: LA (Lower Alabama)
Posts: 276
|
Re: Modified EZ Go won't go
Thanks JohnnieB! I read some of your other posts and thought the same, however wanted to be sure before dropping the dough on a replacement.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
modified workhorse | Gas EZGO | |||
Modified EZ Go won't go | Extreme DC! | |||
Modified 85 CC, Need advise | Gas Club Car | |||
Just modified my governor on my DS..? | Gas Club Car | |||
modified solenoid | Electric Yamaha |