|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
09-29-2018, 06:10 PM | #1 |
Not Yet Wild
Join Date: Feb 2017
Posts: 69
|
Xct400 error code
Need a little help guys. Got a 2011 txt 48, installed alltrax xct400 and 200 amp solenoid. Been working fine till today. Cart will only jerk fwd and reverse. Throwing precharge code. 1 green 6 red flash’s. Any help will be greatly appreciated.
Sent from my iPhone using Tapatalk |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-29-2018, 09:59 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Xct400 error code
Look at the blink codes in the back of the owners manual- what does it say for 1grn 6 red?
|
09-30-2018, 07:53 AM | #3 |
Not Yet Wild
Join Date: Feb 2017
Posts: 69
|
Re: Xct400 error code
Precharge failure
Sent from my iPhone using Tapatalk |
09-30-2018, 07:55 AM | #4 |
Not Yet Wild
Join Date: Feb 2017
Posts: 69
|
Re: Xct400 error code
Stuck solenoid is what the book says.
Sent from my iPhone using Tapatalk |
09-30-2018, 12:05 PM | #5 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Xct400 error code
|
09-30-2018, 12:32 PM | #6 |
Not Yet Wild
Join Date: Feb 2017
Posts: 69
|
Re: Xct400 error code
Yes. It’s the same.
Sent from my iPhone using Tapatalk |
09-30-2018, 12:39 PM | #7 |
Not Yet Wild
Join Date: Feb 2017
Posts: 69
|
Re: Xct400 error code
Here is what’s weird, just turned it on went around the block like nothing was wrong. It has done this previously but I would turn the key off and back on and it would be fine.
Sent from my iPhone using Tapatalk |
09-30-2018, 04:43 PM | #8 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Xct400 error code
Okay - so the controller problem has a history. Maybe you should be looking at the cart, not the new controller, for a solution.
In between the controller and the pedal box is a wire harness pug with 4 wires where both the input and output throttle signal as well as the solenoid activation signal go through. This plug gets wet, dirty, and corroded. It is a know trouble spot in the TXT cart. Some people simply cut the plug out and use connectors or solder in place. GL |
10-01-2018, 07:58 AM | #9 |
Not Yet Wild
Join Date: Feb 2017
Posts: 69
|
Re: Xct400 error code
Ok, I will definitely check that out. I’m very pleased with the performance of the new controller. It’s all I needed! Last weekend my father-law and rode around the hunting club for 3 hrs and the cart never struggled one bit! So impressed!
|
10-07-2018, 04:20 PM | #10 |
Not Yet Wild
Join Date: Feb 2017
Posts: 69
|
Re: Xct400 error code
Does the pre charge resistor need to be hooked upped on the new Solenoid? I thought I read that it didn’t need to be. I checked the 4 pin plug all seems to be good. Just drove the cart yesterday and it acted upped, I turned the key off and back on it was fine.
Sent from my iPhone using Tapatalk |
|
|
Similar Threads | ||||
Thread | Forum | |||
Ezgo pds - won't go 1-4 error code | Electric EZGO | |||
alumacar problem / error code? | Electric Club Car | |||
Xct400 fault code- motor feild failure? | Electric Club Car | |||
2 Green and 3 Red Altrax SPM error Code | Electric EZGO | |||
DPI Error Code | Electric Club Car |