|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
02-09-2010, 09:35 AM | #11 |
Gone Wild
Join Date: Nov 2009
Location: mi
Posts: 766
|
Re: removing govner on g1
ok so i will wire it open but is this going to effect the oil pump vacum line that goes to the header
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-09-2010, 04:24 PM | #12 |
Gone Wild
Join Date: Nov 2007
Location: Martinsburg, WV
Posts: 651
|
Re: removing govner on g1
GMB is correct Lady Bug I wired mine open but I dont fool with the oil injector I took all that off because I pre mix my oil in the gas tank. I run the heck out of my 81 G1 mostly full throttle at all times so I wanted to make sure it got enough oil to the engine.
Calvin |
02-09-2010, 05:46 PM | #13 |
Gone Wild
Join Date: Nov 2009
Location: mi
Posts: 766
|
Re: removing govner on g1
what do you mix it at and how do you plug the hose off the carb with a screw or something
|
02-09-2010, 05:53 PM | #14 |
Gone Wild
Join Date: Jul 2008
Location: Reddick IL
Posts: 11,220
|
Re: removing govner on g1
I run the injecter one less can of gas sitting to worry about.
|
02-10-2010, 07:03 PM | #15 |
Gone Wild
Join Date: Nov 2009
Location: mi
Posts: 766
|
Re: removing govner on g1
if i keep the oil injector is there any possibility that i can drill out the governor arm that sits on the rear end so that the spline just wont be able to turn it?
|
05-13-2010, 04:33 PM | #16 |
Not Yet Wild
Join Date: May 2010
Posts: 54
|
Re: removing govner on g1
That's what i was wondering too, drill out the arm and leave the bolt out then drill and tap a hole in the top of the gov shaft for a small bolt and washer to keep the arm in place and just let it float on the shaft.
|
05-17-2010, 11:36 PM | #17 |
Not Yet Wild
Join Date: May 2010
Posts: 54
|
Re: removing govner on g1
|
05-18-2010, 04:39 AM | #18 |
Gone Wild
Join Date: Jun 2009
Location: Heluvabump,VT
Posts: 623
|
Re: removing govner on g1
Somebody on here has done just that. Do a search for the thread. I think they even had pictures of how they did it.
|
05-18-2010, 08:24 AM | #19 |
Not Yet Wild
Join Date: May 2010
Posts: 54
|
Re: removing govner on g1
Tried the search but can't find anything that applies to a gas G1?
|
05-18-2010, 08:32 AM | #20 |
Gone Wild
Join Date: Nov 2007
Location: Martinsburg, WV
Posts: 651
|
Re: removing govner on g1
I done mine this way since the arm broke off completely.
Calvin |
|
|
Similar Threads | ||||
Thread | Forum | |||
Removing cowl on Par Car? | Electric golf carts | |||
Removing body on a G8 | Gas Yamaha | |||
removing body? | Electric golf carts | |||
Removing key ignition | Electric EZGO | |||
Govner/rev limiter Q??? HELP!!!! | Gas Club Car |