|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
06-26-2015, 01:54 PM
|
#1 |
|
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Picked up a BV24 for my cart and have a question
Picked up a BV24 for my cart and have a question about the throttle. As some of you know I have a 1989 3pg which is a pull throttle with governor and all linkage removed, the BV24 I picked up off a 1988 2pg is a push throttle (spring holds throttle WFO!) with a pressed on linkage. I have not left work yet to mess with it but would like some ideas before I get to work on it. Is it as simple as changing spring position? I will get a better look at it when I get home.
Thanks, Scott |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-26-2015, 05:08 PM
|
#2 |
|
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: Picked up a BV24 for my cart and have a question
I ASSume I will just disconnect the shaft spring and rig up a return spring like I have it set up now.
|
|
|
|
|
06-26-2015, 06:17 PM
|
#3 |
|
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: Picked up a BV24 for my cart and have a question
Ok, got home tore down the carb to clean it, throttle shaft was not pressed so I pulled the linkage and looked through my other carbs and found the correct spring on another bv18 I had.......All Good!
|
|
|
|
|
06-26-2015, 08:27 PM
|
#4 | |
|
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: Picked up a BV24 for my cart and have a question
Quote:
|
|
|
|
|
|
06-29-2015, 08:48 AM
|
#5 |
|
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: Picked up a BV24 for my cart and have a question
Well the BV24 seems a little fat, I am doing the HEI this week so I will see how it does after that. I picked it up cheap so I figured it was worth a shot.
|
|
|
|
|
07-02-2015, 06:15 AM
|
#6 |
|
Gone Wild
Join Date: Oct 2009
Location: West Virginia
Posts: 291
|
Like to see some pics of your throttle linkage area.
|
|
|
|
|
07-02-2015, 07:21 AM
|
#7 |
|
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: Picked up a BV24 for my cart and have a question
Fist pics are as I had it with a different Mikuni and straight manifold but I had issues getting enough throttle pull which also created slow speed issues, the last picture is the way it is now (back to stock) with the BV24.
   |
|
|
|
|
07-02-2015, 08:21 AM
|
#8 |
|
Gone Wild
Join Date: Oct 2009
Location: West Virginia
Posts: 291
|
I appreciate the pics. Especially the last one. Forgive my ignorance, but you have the governor screw tightened all the way down and have it directly to the carb? With it being that way I see there is no return spring needed. What kind of motor hazards are present with bypassing the governor.
|
|
|
|
|
07-02-2015, 10:18 AM
|
#9 |
|
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: Picked up a BV24 for my cart and have a question
Is the governor arn hooked up, or loose on the shaft and acting merely as a pivot/ratio-increaser?
|
|
|
|
|
07-02-2015, 04:34 PM
|
#10 |
|
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: Picked up a BV24 for my cart and have a question
Terry, who are you asking? The shaft is flat sided so I is not just a pivot point but it has no effect on the throttle and I assumed because I have the spring cranked all the way down.
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Picked up another cart | Gas Club Car | |||
| Picked up my first cart. | Members Rides | |||
| Picked up yet another cart but.... | Electric Club Car | |||
| WTF is this cart I just picked up???? | Members Rides | |||
| Rebuild or BV24 swap? | Gas EZGO | |||
Linear Mode
