|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
12-21-2017, 01:26 PM
|
#11 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G14a transmission
Besides, buying the gasket is probably cheaper than a tube of snot. Gasket IS still available.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
02-04-2018, 04:26 AM
|
#12 |
|
Not Yet Wild
Join Date: Jun 2012
Location: Iowa
Posts: 59
|
Re: G14a transmission
Ok, I have the high speed gears in now and sorry to say the low end is bad. Not sure how it will act on some of the hills around here. I noted that the secondary sheave and spring seat have different holes for the spring. I have it in B and 3 as service states. how does changing the holes affect the clutch? Thanks much guys.
|
|
|
|
|
02-04-2018, 05:12 AM
|
#13 | |
|
Gone Wild
Join Date: Jun 2015
Location: Philippines
Posts: 570
|
Re: G14a transmission
Quote:
|
|
|
|
|
|
02-05-2018, 01:20 AM
|
#14 |
|
Not Yet Wild
Join Date: Jun 2012
Location: Iowa
Posts: 59
|
Re: G14a transmission
Where does the spacer go? Thanks for the info.
|
|
|
|
|
02-05-2018, 02:17 AM
|
#15 |
|
Gone Wild
Join Date: Jun 2015
Location: Philippines
Posts: 570
|
Re: G14a transmission
On this images, you should see the spacer which replaces the circlip out of the transmission, then shown once installed...
Please note all pictures were posted in this forum and are not mine... |
|
|
|
|
02-05-2018, 12:12 PM
|
#16 |
|
Not Yet Wild
Join Date: Jun 2012
Location: Iowa
Posts: 59
|
Re: G14a transmission
So the spacer goes behind the spring seat. Thanks.
|
|
|
|
|
02-05-2018, 08:14 PM
|
#17 | |
|
Gone Wild
Join Date: Jun 2015
Location: Philippines
Posts: 570
|
Re: G14a transmission
Quote:
|
|
|
|
|
|
02-17-2018, 09:35 PM
|
#18 |
|
Not Yet Wild
Join Date: Jun 2012
Location: Iowa
Posts: 59
|
Re: G14a transmission
I installed a new high torque secondary spring with the spacer. It ran well but then the 4th time out it blew the belt. Is there a heavier belt required for that spring add on?
|
|
|
|
|
02-17-2018, 10:05 PM
|
#19 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G14a transmission
Yamaha used the stock belt with their UMAX spring, but all bets are off for the crazy springs that are out there.
|
|
|
|
|
02-17-2018, 11:10 PM
|
#20 |
|
Gone Wild
Join Date: Jun 2015
Location: Philippines
Posts: 570
|
Re: G14a transmission
Strange, when I first installed the spring (from CPP), I was using the original Yamaha belt and had no trouble for almost 1.5 years...
When I installed the High speed gear, I switched at the same time to the GBoost Severe duty; a really good belt! |
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| G14a won't start | Gas Yamaha | |||
| Old Yamaha G14a is dying | Gas Yamaha | |||
| CPP speed spring for G14A | Gas Yamaha | |||
| g14a wont turnover | Gas Yamaha | |||
| G14A Starter wiring | Gas Yamaha | |||
Linear Mode
