lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Yamaha
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles



Post New Thread  Reply
 
Thread Tools Display Modes
Old 09-26-2018, 09:08 PM   #1
typical.t
Not Yet Wild
E-Z-GO
 
Join Date: Feb 2013
Location: Nw Indiana
Posts: 38
Default G2 replaced F&R cables,input shaft,and driven clutch with no F&R

Replaced the F&R cables ,input shaft,and driven clutch. After weeks of adjusting still can't get ot to stay in gear and or I lose one or the other.or both Not sure what I missed or not seeimg any help would be great when it does stay in forward right before you come to a complete stop it will jump out of gear. And not lock back in gear
typical.t is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 10-08-2018, 01:45 AM   #2
dacheedah
Gone Wild
 
dacheedah's Avatar
Yamaha
 
Join Date: Sep 2017
Location: Kankakee, Il
Posts: 194
Default Re: G2 replaced F&R cables,input shaft,and driven clutch with no F&R

Any luck?


Sent from my iPhone using Tapatalk
dacheedah is offline   Reply With Quote
Old 10-08-2018, 06:37 AM   #3
typical.t
Not Yet Wild
E-Z-GO
 
Join Date: Feb 2013
Location: Nw Indiana
Posts: 38
Default Re: G2 replaced F&R cables,input shaft,and driven clutch with no F&R

I have not.
typical.t is offline   Reply With Quote
Old 10-08-2018, 08:13 AM   #4
BBBHC
Gone Wild
 
BBBHC's Avatar
Club Car
 
Join Date: Jul 2018
Location: Central Ohio
Posts: 1,720
Default Re: G2 replaced F&R cables,input shaft,and driven clutch with no F&R

If you can post pictures of the install, one of us might see something
BBBHC is offline   Reply With Quote
Old 10-08-2018, 11:48 AM   #5
TheNewGuy
Admin/Moderator
 
TheNewGuy's Avatar
Yamaha
 
Join Date: Dec 2006
Location: Ohio
Posts: 18,009
Default Re: G2 replaced F&R cables,input shaft,and driven clutch with no F&R

Quote:
Originally Posted by BBBHC View Post
If you can post pictures of the install, one of us might see something
I agree, some pics!

TheNewGuy is offline   Reply With Quote
Old 10-09-2018, 02:07 PM   #6
typical.t
Not Yet Wild
E-Z-GO
 
Join Date: Feb 2013
Location: Nw Indiana
Posts: 38
Default Re: G2 replaced F&R cables,input shaft,and driven clutch with no F&R

I will do
typical.t is offline   Reply With Quote
Old 10-10-2018, 09:36 AM   #7
typical.t
Not Yet Wild
E-Z-GO
 
Join Date: Feb 2013
Location: Nw Indiana
Posts: 38
Default Re: G2 replaced F&R cables,input shaft,and driven clutch with no F&R

20181009_201505-1_(1)[1].jpg

20181009_201515-1_(1)[1].jpg

I will try and get better pic. tonight I know the cables are not adjusted I took these late last night and that how I left ti from last time I work on It I have turn the bracket on the transaxle around both way still no go any advise will be helpful
typical.t is offline   Reply With Quote
Old 10-13-2018, 07:10 PM   #8
sho305
Vegas modded 420
 
sho305's Avatar
Yamaha
 
Join Date: Jun 2009
Location: West MI
Posts: 15,433
Default Re: G2 replaced F&R cables,input shaft,and driven clutch with no F&R

The cables do have to be tightened against each other (tighten both), pretty sure that is what the springs are on them for. If you don't it wont stay in gear, if you tighten too much it will be hard to shift. Also need to center the shifter. I roll the cart by hand or you can take the drive belt off and turn the secondary, and move the shifter very slowly from center to see where it hits the gears. Then adjust one up and one down to get it centered or very slightly more into forward but very close to same. Lube the shifter shaft to make it work easier if needed, mine was dry and it helped. Far as tightness of cables It should pop into gear and stay, but not be too hard to shift that it is uncomfortable to do (and I get yelled at lol). Fiddle with the cable adjustment until you get it, then likely you will never have to touch it again. Adjust them opposite to move neutral, adjust both the same to tighten or loosen shift action.

Here is pics of mine if it helps
http://www.buggiesgonewild.com/gas-y...placement.html
sho305 is offline   Reply With Quote
Old 10-15-2018, 08:16 PM   #9
typical.t
Not Yet Wild
E-Z-GO
 
Join Date: Feb 2013
Location: Nw Indiana
Posts: 38
Default Re: G2 replaced F&R cables,input shaft,and driven clutch with no F&R

Thank you I will try this. At this point I will Try anything i have adjused and can catch one gear but loose the other so i am going to start over and follow and hopefully i can get it again thank you for the advice
typical.t is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Yamaha


Thread Tools
Display Modes


Similar Threads
Thread Forum
Spring Cap Seized onto Spline / Input Shaft on Secondary Clutch of G16A Gas Yamaha
EZGO Rear differential input shaft nut crimped? how to remove input shaft?! Gas EZGO
axle clutch input shaft Electric Yamaha
Replaced input shaft bearings 06 TXT Electric EZGO
Driven Clutch Seized to the Shaft Gas Club Car


All times are GMT -5. The time now is 04:47 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.