|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
06-03-2020, 07:22 PM | #21 |
Not Yet Wild
Join Date: Jun 2020
Location: Dardenne Prairie, MO
Posts: 22
|
Re: Yamaha drive axle nut
Thanks again for your time, I really appreciate it, takes some patience dealing with a million questions. I know I have a 4 and 5 year old. One more till I get some work done. If the bearing is on the outside and the axle shaft pulls out do I need to remove the brake hub and the axle tube? Or basically what I took off to inspect the spline and pull it out and remove the bearing?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-03-2020, 08:43 PM | #22 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Yamaha drive axle nut
With the drum & hub off (like you had it), remove the snap ring & the axle shaft can pull out.
|
06-09-2020, 04:10 PM | #23 |
Not Yet Wild
Join Date: Jun 2020
Location: Dardenne Prairie, MO
Posts: 22
|
Re: Yamaha drive axle nut
How and which way does bearing come off? Don’t want to damage anything, it is not sliding off.
|
06-09-2020, 04:20 PM | #24 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Yamaha drive axle nut
It slides toward the outer end (the shorter direction). Its a light press fit.
|
06-09-2020, 05:11 PM | #25 |
Not Yet Wild
Join Date: Jun 2020
Location: Dardenne Prairie, MO
Posts: 22
|
Re: Yamaha drive axle nut
Does everything need grease on it? It had some blue grease behind the bearing.
|
06-09-2020, 05:38 PM | #26 |
Not Yet Wild
Join Date: Jun 2020
Location: Dardenne Prairie, MO
Posts: 22
|
Re: Yamaha drive axle nut
Put it back together and now the noise is worse. I can drive it 3’ and brake and hear the noise. Even worse in reverse.
|
06-09-2020, 05:46 PM | #27 |
Not Yet Wild
Join Date: Jun 2020
Location: Dardenne Prairie, MO
Posts: 22
|
Re: Yamaha drive axle nut
Did not change the transaxle oil though, no wAy I’m going to get it level enough. It is on a 45 degree angle.
|
06-27-2020, 05:35 PM | #28 |
Not Yet Wild
Join Date: Jun 2020
Location: Dardenne Prairie, MO
Posts: 22
|
Re: Yamaha drive axle nut
Update
Took it in and they tightened the brake backing plate, changed the fluid, new brake pads, and tightened up and lubed the pedal. Took care of the noise. Started my lights and the 48v converter keeps blowing the fuse on it. Its a 20 amp fuse. Had it wired to a fuse block so I took that off to see if that was the problem and it keeps blowing. Not sure why, only 3 wires hooked up and they are right. Any ideas? |
06-27-2020, 07:36 PM | #29 |
Gone Wild
Join Date: May 2015
Location: Central Florida
Posts: 2,114
|
Re: Yamaha drive axle nut
Take it back to a shop, that seems to be your best bet.
|
06-28-2020, 03:00 PM | #30 |
Not Yet Wild
Join Date: Jun 2020
Location: Dardenne Prairie, MO
Posts: 22
|
Re: Yamaha drive axle nut
Not really an option, took two weeks to look at last time. The ground wire in the harness is burnt the most. Any reason to think the converter wires are off?
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Yamaha Drive Rear Axle Oil Leak | Electric EZGO | |||
Yamaha Drive Suspension Ideas? and tire and wheel? on Yamaha Drive with a 600cc motor | On Road Golf Carts! | |||
Cbr 600 F3 engine going into Yamaha Drive (Have Axle Question??) | Bike & ATV Engine Swaps | |||
G29 drive axle nut | Electric Yamaha | |||
drive axle | Electric EZGO |