|
10-01-2017, 08:37 AM
|
#1 |
|
Not Yet Wild
Join Date: Jun 2017
Location: South Alberta Canada
Posts: 8
|
Armrest cover
Hi all.
Ok so we are all out overhauling the campground buggy. It's the 1988 marathon Gas model. The aluminum armrest have a black cover over part of it. One of ours is cracked and had been partly replaced with electrical tape. I have searched online and can't find it anywhere. Anyone know where to get this part? Anyone know either the armrest or cover part number? Still looking for manual and part diagram list, please if you have or know location I would love to get it. "Dooh!!!, it's my first day." |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
10-01-2017, 09:51 AM
|
#2 |
|
Guest
Posts: n/a
|
Re: Armrest cover
i did a melex with black spray plast-dip
has held up for 2 years  |
|
|
|
10-02-2017, 05:03 AM
|
#3 |
|
Gone Wild
Join Date: Mar 2016
Location: Brookings, SD
Posts: 216
|
Re: Armrest cover
Flex Seal (like seen on TV) works good too. It comes in spray, liquid dip, or in a caulk tube. I sprayed my rear seat step and it is now not slippery when it get wet. I used it on both sides of the floor board when I had it off. More durable than spray under coating. I think it comes in black, silver, white and clear.
|
|
|
|
|
10-02-2017, 09:48 PM
|
#4 |
|
Not Yet Wild
Join Date: Jun 2017
Location: South Alberta Canada
Posts: 8
|
Re: Armrest cover
Great ideas guys, I never thought of that.
Awesome. |
|
|
|
|
10-03-2017, 12:58 PM
|
#5 |
|
Nincompoop Club Member
Join Date: Jun 2016
Location: Idaho
Posts: 1,178
|
Re: Armrest cover
I'm always looking for a good reason to get into a 3D printer, this part would be a great one. Maybe you could find someone with one, Good Luck
|
|
|
|
|
10-20-2017, 08:38 AM
|
#6 |
|
Not Yet Wild
Join Date: Jun 2017
Location: South Alberta Canada
Posts: 8
|
Re: Armrest cover
3D printer... hummmm.
I just came up with an excuse to feed my wife to allow me to buy a Plasma cutter. I'll have to run the damaged plastic arm rest cover and 3D printer idea by her. Lol That may be pressing my luck. One time the squeaky wheel got the grease but now a days the squeaky wheel gets replaced. |
|
|
|
|
10-31-2017, 11:05 AM
|
#7 |
|
Nincompoop Club Member
Join Date: Jun 2016
Location: Idaho
Posts: 1,178
|
Re: Armrest cover
LOL...... Good for ya on the plasma cutter, I'd rather have one of those anyway. But you could always just tell her the 3D printer is part of a complete Plasma cutting system :)
|
|
|
|
|
10-31-2017, 11:25 AM
|
#8 |
|
......................
 Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: Armrest cover
|
|
|
|
 |
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| club car carryall armrest question | Gas Club Car | |||
| New armrest on older cart? | Design Center | |||
| Driven clutch dust cover very close to engine air cover | Gas EZGO | |||
| Rear seat armrest cushion | Electric Club Car | |||
| Rear Seat Armrest Bar (Pic): Can one buy this separate? | Electric EZGO | |||
Linear Mode
