|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
04-21-2015, 08:40 PM | #1 |
My wife says I'm crazy...
Join Date: Sep 2014
Location: Central Ohio
Posts: 384
|
96 g16 carb
Ok, working on installing new carb on g16, and I have an issue. the diagram shows the following:
airbox--gasket--carb--gasket--joint--gasket--engine. The joint is Yami part JN6-13595-00-00. My problem is I don't have a joint. It goes strait from carb to gasket to engine. Am I missing something here, or is this something that happened in 1996 when the g14 to g16 switch happened? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-22-2015, 06:07 AM | #2 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
Re: 96 g16 carb
As far as I know, the joint/spacer is supposed to be there on all G16's. If you have a new carb, get the joint and do it up right.
|
04-22-2015, 07:04 AM | #3 |
My wife says I'm crazy...
Join Date: Sep 2014
Location: Central Ohio
Posts: 384
|
Looks like the spacer would move airbox out and wouldn't that affect the rear bolts on air box?
|
04-22-2015, 07:39 AM | #4 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
Re: 96 g16 carb
Yes, it seems like it would, but the joint needs to be there. Not sure if the carb will even attach to the head without it, unless the shroud is missing.
|
04-22-2015, 02:31 PM | #5 |
My wife says I'm crazy...
Join Date: Sep 2014
Location: Central Ohio
Posts: 384
|
I picked it up and going to attempt tomorrow. Maybe that piece is there and I'm not looking at it right, because that part is wider than I thought
|
04-23-2015, 03:33 PM | #6 |
My wife says I'm crazy...
Join Date: Sep 2014
Location: Central Ohio
Posts: 384
|
And I get to humble myself on this one. It was there. The key word was shroud Dave. Wasn't even thinking it would be recessed. Thanks. Now it's off to cleaning air box and pulling starter generator to replace brushes.
|
04-27-2015, 01:45 PM | #7 |
My wife says I'm crazy...
Join Date: Sep 2014
Location: Central Ohio
Posts: 384
|
Re: 96 g16 carb
Guess closure on this. I was able to install new carb with lifted cart jet with little to no problem. Replaced all lines in and out while I was at it, and after all was hooked up she runs like a champ with no adjustments to carb. I was worried that I would be in for a series of adjustments but it's perfect.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
carb tuning mikuni or eBay CV carb | Clone Engine Swaps | |||
1989 Ezgo New Carb leaking gas like the old Carb | Gas EZGO | |||
cheap carb swap onto 3PG engine- Tecumseh carb works great- with lots of pics | Gas EZGO | |||
need used carb or carb parts (87 ezgo) | Golf Carts and Parts | |||
91 2 Cycle Carb Missing Carb Screw | Gas EZGO |