|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
02-27-2017, 05:33 PM
|
#1 |
|
Gone Wild
Join Date: Jan 2015
Location: new lebanon, OH
Posts: 758
|
RXV governor adjustment
just picked up an 09 rxv 13.5 kaw. wondering if they are adjusted the same as an ezgo txt? tried searching the forum and tech but no luck
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
02-28-2017, 06:07 PM
|
#2 |
|
Gone Wild
Join Date: Apr 2012
Location: Dansville, NY
Posts: 396
|
Re: RXV governor adjustment
There is no gov. adjustment. You would have to attach a heavier spring to the end of the throttle cable. Run the throttle cable adjustment at the diff. to the end of the threads, then bend the cable bracket outward some will give you shorter throw at the pedal and a little heavier pull on the gov. Be careful how much you bend the bracket so as not have the throttle move before the ignition comes on. About a 1/4" will be close.
|
|
|
|
|
02-28-2017, 08:01 PM
|
#3 |
|
Gone Wild
Join Date: Jan 2015
Location: new lebanon, OH
Posts: 758
|
Re: RXV governor adjustment
any idea if 25's will fit on these with a 6" spindle lift?
|
|
|
|
|
02-28-2017, 10:13 PM
|
#4 |
|
Gone Wild
 Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,141
|
Re: RXV governor adjustment
No gov adjustment? Hmmm.. I tweeked mine to just hit 4K rpm unloaded with 21 inch tires at roughly 25 mph. The governor is different but can be adjusted.
|
|
|
|
|
03-01-2017, 01:45 PM
|
#5 |
|
Gone Wild
Join Date: Jan 2015
Location: new lebanon, OH
Posts: 758
|
Re: RXV governor adjustment
just not like the txt?
|
|
|
|
|
03-01-2017, 04:50 PM
|
#6 |
|
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,141
|
Re: RXV governor adjustment
Found a write up I did on how I adjusted mine..
Take the throttle cable out of the bracket, loosen the 10mm nut on the gov bracket and get it where when the pedal is pushed it will start and idle. Then loosen the nut/bolt holding the governor to the shaft and make sure it is spun all the way against its backstop. Mine wasn't. Then hold the throttle against idle, the gov against its stop and tighten the 10mm nut. Now hook your cable back up and tweak. Mine with 21 inch tires runs 26 at 4k rpm |
|
|
|
|
03-08-2017, 02:45 PM
|
#7 |
|
Gone Wild
Join Date: Jan 2015
Location: new lebanon, OH
Posts: 758
|
Re: RXV governor adjustment
awesome thanks
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| G1 Governor adjustment | Gas Yamaha | |||
| Governor adjustment? WOT help! | Big Block Talk! | |||
| Governor rod adjustment | Gas Club Car | |||
| Governor adjustment | Gas EZGO | |||
| governor adjustment | Gas Club Car | |||
Linear Mode
