|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
11-06-2018, 09:05 PM | #1 |
Getting Wild
Join Date: Apr 2009
Location: The Ville
Posts: 81
|
How to pull/remove G1 engine?
I have an 81 gas G1 that I want to remove the engine so I can clean everything up as well as replace the seals and wiring. The carb and cables are already disconnected. Looks like exhaust, belts and wiring are all that's left to unhook. I saw a picture earlier of a frame with no engine. It looks like 4 bolts facing up connected to the frame, 2 in front, 2 in back. I'll have to find them under all the nastiness and take the nuts off from the top and lift the engine out? Thanks for any help.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-07-2018, 12:21 PM | #2 | |
Gone Wild
Join Date: Jan 2017
Location: venice
Posts: 1,807
|
Re: How to pull/remove G1 engine?
Quote:
the wires are all color coded and should be pretty straight forward. check and clean all terminals. use some electrical grease when reassembling. All cables from battery to starter/gen and to solenoids should be inspected/ cleaned and or replaced. These cables are know issues with the age of these carts and cause a lot of weird symptoms. |
|
11-07-2018, 08:21 PM | #3 |
Gone Wild
Join Date: Jan 2017
Location: venice
Posts: 1,807
|
Re: How to pull/remove G1 engine?
|
11-08-2018, 08:21 PM | #4 |
Getting Wild
Join Date: Apr 2009
Location: The Ville
Posts: 81
|
Re: How to pull/remove G1 engine?
Thanks mikeasis. Hopefully I'll get some extra time soon and get it out.
|
11-09-2018, 07:59 AM | #5 |
Gone Wild
Join Date: Jun 2012
Location: Spicewood, TX
Posts: 219
|
Re: How to pull/remove G1 engine?
One more quick word of advice. Get the G1 repair manual. Section 3 of the manual describes engine removal, and has a good list of things to disconnect before you remove the engine.
HTH, Ogre |
11-09-2018, 06:20 PM | #6 |
Getting Wild
Join Date: Apr 2009
Location: The Ville
Posts: 81
|
Re: How to pull/remove G1 engine?
I have downloaded the manual and looked over that section. Thanks.
|
11-13-2018, 07:46 PM | #7 |
Gone Wild
Join Date: Jan 2017
Location: venice
Posts: 1,807
|
Re: How to pull/remove G1 engine?
Looks like this
|
11-13-2018, 08:42 PM | #8 |
Getting Wild
Join Date: Apr 2009
Location: The Ville
Posts: 81
|
Re: How to pull/remove G1 engine?
That's perfect mikeasis. Thanks for the picture! I'll take it out that way and put it on the bench. If I only had more time and more room in the garage, I could put the whole cart in the garage. I think it will work out better this way by putting the engine on the work bench. Thanks again.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Pull behind bar? | Design Center | |||
Best way to pull engine on G16? | Gas Yamaha | |||
How do I remove the head from robin engine | Gas EZGO | |||
1984 Ez-go remove clutch engine still in? | Gas EZGO |