|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
06-16-2014, 05:02 PM | #11 |
Not Yet Wild
Join Date: Feb 2012
Posts: 9
|
Yes I check B- to A2 on motor got same read as B-to A1
Sent from my iPhone using Tapatalk |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-16-2014, 06:11 PM | #12 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 08 PDS wont run
Quote:
It ought to be full battery pack voltage when the solenoid clicks. If not, the solenoid contacts are bad, or the two high current cables that connect the battery to the solenoid and the solenoid to A2 on motor. |
|
06-17-2014, 06:59 AM | #13 |
Not Yet Wild
Join Date: Feb 2012
Posts: 9
|
Re: 08 PDS wont run
Yes both places were same 1.0 at half and 0 at full it read 5to 6 for half sec therm 0
|
06-17-2014, 07:18 AM | #14 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 08 PDS wont run
If you are not only getting full battery pack voltage on the A2 motor terminal after the solenoid has clicked, one of four things is bad.
1. The cable from the battery pack's main positive terminal to the solenoid. 2. The cable from the battery pack's main positive terminal to the B- terminal on the controller. 3. The cable from the solenoid to the A2 stud on the motor. 4. The solenoid contacts. |
06-17-2014, 04:06 PM | #15 |
Not Yet Wild
Join Date: Feb 2012
Posts: 9
|
Re: 08 PDS wont run
i went to get reading again i seen i was charging cart took off charger , so when i took reading again B- To A1 i had 36.0 i pressed padel half to hear solenoid the cart started to move, i took meter off and thied again the cart dont move now and readings are B- To A1 is 7.3 Half 3.0 full 0 also B- To A2 on motor reads the same
|
06-18-2014, 06:15 AM | #16 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 08 PDS wont run
Quote:
If you are not getting FULL battery pack voltage at A2 when the solenoid clicks, the problem is one of the following: 1. The cable from the battery pack's main positive terminal to the solenoid. 2. The cable from the battery pack's main positive terminal to the B- terminal on the controller. 3. The cable from the solenoid to the A2 stud on the motor. 4. The solenoid contacts. BTW: If your battery pack voltage is only 36.0V and the battery pack just came off the charger (as eluded to in your first sentence) your battery pack is only charging to 43% SoC, so your batteries are bad and/or your charger is broken. |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Ezgo dcs solenoid clicks but wont disengage and wont move | Electric EZGO | |||
wont run | Gas EZGO | |||
Wont turn left and now wont turn right | Electric EZGO | |||
EZ-wont GO | Gas EZGO | |||
wont run | Gas EZGO |