G16e

Otter70 · 10-06-2008, 03:44 PM

My previous post was a mistake. I still need the help though.

My buddys yammy stopped dead in its tracks. How do I test the soleniod and the controller? Thanks in advance for the help

roady89 · 10-06-2008, 07:32 PM

Most people try jumping the solenoid....if it runs jumped the solenid is bad. Depending on the controller you may have to bench test it. If it's a yamaha controller, I'm not sure how to test those.

Otter70 · 10-06-2008, 07:58 PM

Roady, thanks for the reply. I heard that yamaha controllers are crap so I think I'm gonna replace it with an alltrax. the solenoid tests good.

Otter70 · 10-09-2008, 02:52 PM

Does anyone on here know where I can get the 2 diodes that are in the wiring harness for this g16? I figured I'd go ahead and replace those too.

Otter70 · 10-12-2008, 05:09 PM

I need a wiring diagram to wire the AXE 4844 to the wiring that goes to the throttle and other wires that the stock controller is wired to. The wires that come out of the stock controller connect to the Key switch, back switch, limit switch, buzzer, and the accelerator stop switch.

Thanks

Otter70 · 10-19-2008, 11:36 AM

I have been in contact with Chuck at Alltrax. First, let me say that the customer support is second to none. I got the AXE 4844 installed, new 4 ga wiring, new White Rodgers 586-907 contactor. The only thing I haven't upgraded is the FnR switch. This is a series cart. The FnR looks like its a sealed unit. Does anyone know where I can get a HD FnR for this cart?

coffincustoms · 07-24-2011, 01:05 AM

Otter, what did you end up with for the 4 wires into the Alltrax. I'm piecing mine back together and mis labeled the wires. Thanks

mikey151 · 06-23-2014, 12:58 AM

Yamaha doesn't make a hd f and r switch you have to go with a hd f and r contactor it replaces the entire forward and reverse system with two connected contactors and replace the lever with a switch. I went through the same with my g16 but the switch is way better and can handal more amps I got mine from Scottyb at cartsunlimited

Lifted G16 · 06-24-2014, 12:55 PM

mikey151- How much did the F&R Contactor run you?

Otter70- They do not make a HD F&R switch for a G16. What I did with the help of Scottyb is use a EZ-GO HD F&R switch that used a 1989-94 center pivot shaft with a EZGO shift handle with minor modifications.

10-06-2008, 03:44 PM	#1
Otter70 Gone Wild Join Date: Feb 2008 Location: Virginia Beach, Virginia Posts: 234	G16e My previous post was a mistake. I still need the help though. My buddys yammy stopped dead in its tracks. How do I test the soleniod and the controller? Thanks in advance for the help

10-06-2008, 07:32 PM	#2
roady89 nimda Join Date: Jun 2007 Posts: 13,023	Re: G16e Most people try jumping the solenoid....if it runs jumped the solenid is bad. Depending on the controller you may have to bench test it. If it's a yamaha controller, I'm not sure how to test those.
roady89 nimda Join Date: Jun 2007 Posts: 13,023

10-06-2008, 07:58 PM	#3
Otter70 Gone Wild Join Date: Feb 2008 Location: Virginia Beach, Virginia Posts: 234	Re: G16e Roady, thanks for the reply. I heard that yamaha controllers are crap so I think I'm gonna replace it with an alltrax. the solenoid tests good.

10-09-2008, 02:52 PM	#4
Otter70 Gone Wild Join Date: Feb 2008 Location: Virginia Beach, Virginia Posts: 234	Re: G16e Does anyone on here know where I can get the 2 diodes that are in the wiring harness for this g16? I figured I'd go ahead and replace those too.

10-12-2008, 05:09 PM	#5
Otter70 Gone Wild Join Date: Feb 2008 Location: Virginia Beach, Virginia Posts: 234	Re: G16e I need a wiring diagram to wire the AXE 4844 to the wiring that goes to the throttle and other wires that the stock controller is wired to. The wires that come out of the stock controller connect to the Key switch, back switch, limit switch, buzzer, and the accelerator stop switch. Thanks

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

10-19-2008, 11:36 AM	#6
Otter70 Gone Wild Join Date: Feb 2008 Location: Virginia Beach, Virginia Posts: 234	Re: G16e I have been in contact with Chuck at Alltrax. First, let me say that the customer support is second to none. I got the AXE 4844 installed, new 4 ga wiring, new White Rodgers 586-907 contactor. The only thing I haven't upgraded is the FnR switch. This is a series cart. The FnR looks like its a sealed unit. Does anyone know where I can get a HD FnR for this cart?

07-24-2011, 01:05 AM	#7
coffincustoms Not Yet Wild Join Date: Jul 2011 Location: Orange County, CA Posts: 3	Re: G16e Otter, what did you end up with for the 4 wires into the Alltrax. I'm piecing mine back together and mis labeled the wires. Thanks

06-23-2014, 12:58 AM	#8
mikey151 Not Yet Wild Join Date: Jun 2014 Posts: 6	Re: G16e Yamaha doesn't make a hd f and r switch you have to go with a hd f and r contactor it replaces the entire forward and reverse system with two connected contactors and replace the lever with a switch. I went through the same with my g16 but the switch is way better and can handal more amps I got mine from Scottyb at cartsunlimited
mikey151 Not Yet Wild Join Date: Jun 2014 Posts: 6

06-24-2014, 12:55 PM	#9
Lifted G16 Not Yet Wild Join Date: May 2013 Location: Palm Bay,FL Posts: 33	Re: G16e mikey151- How much did the F&R Contactor run you? Otter70- They do not make a HD F&R switch for a G16. What I did with the help of Scottyb is use a EZ-GO HD F&R switch that used a 1989-94 center pivot shaft with a EZGO shift handle with minor modifications.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
G16E Help needed	Electric Yamaha
96 g16e wont do anything	Electric Yamaha
96' G16E Will not go	Electric Yamaha