|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
05-12-2017, 03:58 PM | #11 | |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
Quote:
|
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-12-2017, 10:38 PM | #12 |
Gone Wild
Join Date: May 2016
Location: Central Alabama
Posts: 1,042
|
Re: New Altrax Controller on a G22 and having Runaway problems
i had a similar problem with g29 and navitas controller. See my solution in that thread below and see if that helps.
not sure about the alltrax , but navitas required me to change the wiring connections on the controller, i had to split the 2 wires that were made togther |
05-13-2017, 04:55 PM | #13 | |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: New Altrax Controller on a G22 and having Runaway problems
Quote:
|
|
05-23-2017, 02:16 PM | #14 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
|
05-23-2017, 04:55 PM | #15 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
when i have the laptop hooked up everything seems to be working fine, but it wont show my throttle percentage when it goes on runaway mode
|
05-24-2017, 08:23 AM | #16 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
help
|
05-24-2017, 09:03 AM | #17 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: New Altrax Controller on a G22 and having Runaway problems
While I don't know anything specific to Yamaha carts, check where your motor A1 and A2 cables are connected while You wait for help:
High Side Drive: A1 -> M+Low Side Drive (Default for most controllers): A1 -> B+The Alltrax controller emulates M+ on the M- terminal when "High Side Drive" is selected. PS: Keep in mind that Motor Terminals A1 and A2 are interchangeable, the critical information is if any of them is connected to B- or B+. Last edited by Sergio; 05-24-2017 at 09:34 AM.. Reason: Clarification |
05-24-2017, 10:39 AM | #18 | |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
Quote:
|
|
05-24-2017, 03:38 PM | #19 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: New Altrax Controller on a G22 and having Runaway problems
The description of your symptoms: being wired for "High side drive" with no movement when Alltrax is properly configured but full speed when "low side mode" is used:
Means your throttle is not working and stays at 0%. |
05-24-2017, 03:51 PM | #20 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
but the throttle on and off light clicks on when you hit the throttle in the alltrax toolkit. it knows when the throttle is on it just isnt registering a percentage.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Altrax XCT Controller | Electric EZGO | |||
Altrax SPM500 controller map | Electric Club Car | |||
EZGO DCS Altrax Controller, PQ Motor | Golf Carts and Parts | |||
instaling an altrax controller | Electric Club Car | |||
Altrax Controller Recommendations | Electric EZGO |