|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
04-20-2020, 08:46 AM | #1 |
Not Yet Wild
Join Date: Apr 2020
Posts: 4
|
2001 ezgo pds issue. wont go. all new parts
Hello everyone hoping someone could assist me. heres the details I bought this cart not running with no history at all. I replaced the controller as the old one had apparent physical melting and wouldn't beep when put into reverse.
2001 Ez go 36v PDS cart F?R rocker switch on dash I've replaced with all new batteries, new controller and new solenoid. when cart is shifted into forward or reverse solenoid does not click. when in reverse the buzzer does sound. Diagnosing the cart I have bench tested the solenoid and it checks out good. with key on forward selected I have 36 volts at yellow wire on solenoid stud. Reed swith is showing 36v Microswitch for ITS is showing 36v and back traced to J4-1 and J4-2 to confirm at controller ITS is showing .8-.9v with pedal depressed and 2.8V fully pressed. will all hooked up as it should I applied a jumper sending ground to stud on solenoid with blue wire and solenoid clicks and cart will drive forward and back. any ideas why controller isn't sending ground from J1-6 which should energize the solenoid? Thinking maybe a Faulty new controller thanks! |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-20-2020, 09:33 AM | #2 | |
Gone Wild
Join Date: May 2016
Location: Central Alabama
Posts: 1,049
|
Re: 2001 ezgo pds issue. wont go. all new parts
Quote:
|
|
04-20-2020, 09:35 AM | #3 |
Not Yet Wild
Join Date: Apr 2020
Posts: 4
|
Re: 2001 ezgo pds issue. wont go. all new parts
yes I went back with a factory controller. when I do the diag mode it only beeps once after. does nothing else.
|
04-20-2020, 01:45 PM | #4 |
Not Yet Wild
Join Date: Mar 2020
Posts: 2
|
Re: 2001 ezgo pds issue. wont go. all new parts
I have a similar issue. Solenoid wont trigger. Have + voltage to yellow wire, no ground. I ended up having high voltage at ITS so I ordered a replacement. Will see if that fixes it.
|
04-20-2020, 01:50 PM | #5 |
Not Yet Wild
Join Date: Apr 2020
Posts: 4
|
Re: 2001 ezgo pds issue. wont go. all new parts
|
04-20-2020, 06:09 PM | #6 |
Not Yet Wild
Join Date: Mar 2020
Posts: 2
|
Re: 2001 ezgo pds issue. wont go. all new parts
The range should be 1.0-2.7 on the white wire. Mine was at 11v and never changed with pedal movement.
|
04-21-2020, 06:53 AM | #7 |
Not Yet Wild
Join Date: Apr 2020
Posts: 4
|
Re: 2001 ezgo pds issue. wont go. all new parts
my voltage is correct for sure but I just checked the ITS and its showing 8.2 Mega ohms unplugged I believe I was told 3-400 is the correct figure looking for?
|
04-21-2020, 02:26 PM | #8 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 2001 ezgo pds issue. wont go. all new parts
Quote:
Here is a schematic for a ITS sensor. |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
2001 Ezgo workhorse key switch issue | Gas EZGO | |||
2001 EZGO TXT charger issue | Electric EZGO | |||
2001 EZGO tzt wont run or charge batteries | Electric EZGO | |||
2001 EZGO TXT Lighting Issue | Electric EZGO | |||
2001 EZGO TXT - new solenoid wont run | Electric EZGO |