|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
07-14-2013, 10:59 AM | #11 |
Getting Wild
Join Date: Aug 2012
Posts: 100
|
Re: 94 medalist SLOW!
Replaced its with a used one I had and adjusted the plunger even closer to its. Got it to 9.3v between b- and m- also got to a top speed of 17mph. I'm gonna bypass the plastic connector next.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-14-2013, 11:37 AM | #12 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 94 medalist SLOW!
That explains why nothing was getting hot. The controller's output is maxing out at about a 67% duty cycle.
Since the same happens with two different controllers, changing the ITS might fix it. Hopefully it does...... |
07-14-2013, 11:45 AM | #13 |
Getting Wild
Join Date: Aug 2012
Posts: 100
|
Re: 94 medalist SLOW!
Changeling IT'S and adjusting it with 7/32 drill bit dropped us to 8.5v between m- and b-. I'm gonna go to the gym then start rewiring any small wires that look iffy coming from the pedal box. Crossing my fingers we can drop it some more. Reached 18mph on a little downhill today and now spins tires in reverse in grass. If I can get 20 and alright torque by the end of the day, the body can finally go back on. It's been a long ridiculous process with this cart. We have literally upgraded/swapped the f&r, controller, wires, batts, motor, rear end bearings, ITS, pedal box Microswitch, and solenoid. At least it should be reliable haha
|
07-14-2013, 11:48 AM | #14 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 94 medalist SLOW!
Quote:
If the plunger protrudes slightly from the ITS sensor coil when pedal is on floor, that is all the ITS will put out. Also, make sure someone didn't add any brass or copper in or around the ITS coil. That will reduce the inductive reactance, lowering the ITS output. (Brass has the opposite effect that iron has) |
|
07-14-2013, 04:49 PM | #15 |
Getting Wild
Join Date: Aug 2012
Posts: 100
|
Re: 94 medalist SLOW!
Well johnnieb I can't figure it out. Replaced ITS AND plunger today also eliminated the connector as it looked like it had seen better days. Can't get anything less than 9v between b- and m-. I'm out of things to try. Can't figure out how to check voltage on those black and white pins as you have to have them connected to have it run. Should I open the wire sleeve and connect that way or is there a better way to approach this?
|
07-14-2013, 05:37 PM | #16 |
Gone Wild
Join Date: May 2013
Location: Mississippi
Posts: 301
|
Re: 94 medalist SLOW!
The connector should have exposed areas of the pins on one side. See the attached photo:
|
08-03-2013, 08:22 PM | #17 |
Gone Wild
Join Date: Dec 2010
Posts: 635
|
Re: 94 medalist SLOW!
Good Info
|
|
|
Similar Threads | ||||
Thread | Forum | |||
95 medalist very slow uphill | Electric EZGO | |||
95' ez go txt\medalist VERY SLOW to accelerate!!! | Electric EZGO | |||
1994 EZ GO medalist goes slow | Electric EZGO | |||
Slow! How do I make my club car Gasser go really slow. | Gas Club Car | |||
95 ezgo medalist Slow going up hill | Electric EZGO |