|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
01-21-2021, 12:53 PM | #1 |
Not Yet Wild
Join Date: Oct 2020
Posts: 7
|
New wire harness and controller suggestions
I have read through dozens of threads and I am still a little confused as to my best option. I have a 2010 RXV. The local Ezgo distributor told me that either my main wire harness and/or controller needs replacing. Currently I have the Danaher unit.
There are 2 main wire harnesses that I am able to purchase. 609397 without resistor or 619257 I want to get away from the Danaher unit and go with either a Curtis or Navitas. Can anyone tell me what controller is a plug and play for each harness type? Thanks |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
01-21-2021, 03:50 PM | #2 | |
Getting Wild
Join Date: Jan 2020
Location: Indiana
Posts: 139
|
Re: New wire harness and controller suggestions
Quote:
However, the stock numbers that you list are not for the RXV harness. It is 631070. Here is a link to the information https://shop.txtsv.com/electric-harn...sembly-for-rxv. Good luck! |
|
01-21-2021, 06:10 PM | #3 |
Not Yet Wild
Join Date: Oct 2020
Posts: 7
|
Re: New wire harness and controller suggestions
Thanks for the reply molfpedal.
If I have to replace both the harness and the controller my question is, can I go with harness 609379 and if so what controller with match up with that. Or is that not a viable option? |
01-22-2021, 04:51 AM | #4 | |
Gone Wild
Join Date: Mar 2014
Location: NE Indiana & SW Florida
Posts: 3,234
|
Re: New wire harness and controller suggestions
Quote:
1. Curtis RXV Controller 1206AC_52?? 2. Curtis Main Wiring Harness #618955 3. Left controller bracket #623170 4. Right controller bracket #623213 5. Heat shield #623433 6. Resistor .86 ohm #619001 7. 10awg white wire #607707 8. 10awg white wire 400mm #624611 9. 6 Screws #73876G01 10. 2 Screws #649804 11. 2 Screws #00614G04 12. 2 Lock Washers #00565G8 13. 8 Washers #00571G2 If you have a Bearing Encoder you will also need SVC-HARNESS,SENSOR TO ENCODER #612259 The problem with the Navitas conversion is there still using the old main wiring harness. |
|
01-25-2021, 12:44 PM | #5 |
Not Yet Wild
Join Date: Oct 2020
Posts: 7
|
Re: New wire harness and controller suggestions
Thanks usgicollector
I ordered the parts. I will let you know how it works out |
01-30-2021, 05:44 PM | #6 |
Not Yet Wild
Join Date: Oct 2020
Posts: 7
|
Re: New wire harness and controller suggestions
usgicollector
Installed the harness and controller, cart works!!! Thanks so much for the parts list. The only issue was the bearing encoder harness. The large end was female, the small end was male. I needed the opposite. I cut the male end of my old harness and soldered that on to the new one. I got the controller of ebay Golfcartparts 09, the wire harness from Country Cat.com and all the other bits from TXTSV.com. |
01-30-2021, 05:56 PM | #7 |
Gone Wild
Join Date: Mar 2014
Location: NE Indiana & SW Florida
Posts: 3,234
|
Re: New wire harness and controller suggestions
Glad things worked out for you.
|
02-13-2021, 10:36 AM | #8 | |
Gone Wild
Join Date: Mar 2014
Location: NE Indiana & SW Florida
Posts: 3,234
|
Re: New wire harness and controller suggestions
Quote:
This adapter is needed when going from a EZGO RXV Curtis Main Wiring Harness to a Bearing Encoder. When going to a speed sensor no adapter is needed. |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
New Navitas Controller -Where does the blue wire go on the charger harness? | Electric Club Car | |||
Wire harness | Golf Carts and Parts | |||
RXV Disconnect Controller to Trace Wire Harness? | Electric EZGO | |||
RXV wire harness ? | Electric EZGO | |||
2005 Club Car IQ Motor, Wire Harness, & Controller | Golf Carts and Parts |