|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
05-02-2016, 01:36 PM
|
#1 |
|
Not Yet Wild
Join Date: May 2016
Location: Taber Alberta Canada
Posts: 7
|
G16A Sputtering and starting
Golfer here. My cart runs real well at the start of the round but by the 14 hole it starts to buck like it's not getting enough gas Then it sits there trying to start and I have to move gas petal up and down like its starving for gas two or three times and sometimes choke it to get it to move. I have put new carb,new fuel pump and new vacuum and gas hoses on it and it still does it. Replaced air and fuel filters too. Lol any ideas appreciated
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
05-02-2016, 03:20 PM
|
#2 |
|
Gone Wild
Join Date: Mar 2015
Location: Prince George, Va
Posts: 634
|
Re: G16A Sputtering and starting
Welcome to the site!
|
|
|
|
|
05-02-2016, 03:27 PM
|
#3 |
|
Gone Wild
 Join Date: Feb 2007
Location: Southwest Georgia
Posts: 1,469
|
Re: G16A Sputtering and starting
Are you sure its fuel related? Sounds like a coil giving up when it gets hot.
|
|
|
|
|
05-02-2016, 04:55 PM
|
#4 |
|
Not Yet Wild
Join Date: May 2016
Location: Taber Alberta Canada
Posts: 7
|
Re: G16A Sputtering and starting
BigBlockMan. I never thought about the coil. Good idea
|
|
|
|
|
05-03-2016, 07:44 AM
|
#5 |
|
Not Yet Wild
Join Date: May 2016
Location: Taber Alberta Canada
Posts: 7
|
Re: G16A Sputtering and starting
Any suggestions where to buy an ignition coil in USA. Always seems to be cheaper in States than here. eBay ??
|
|
|
|
|
05-03-2016, 08:00 AM
|
#6 |
|
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,314
|
Re: G16A Sputtering and starting
An OEM coil, though expensive, would be best. Many have had problems with the chinese aftermarket knock-offs...
JN6-85640-01-00 TCI unit. Check Amazon. |
|
|
|
|
05-17-2016, 11:09 AM
|
#7 |
|
Not Yet Wild
Join Date: May 2016
Location: Taber Alberta Canada
Posts: 7
|
Re: G16A Sputtering and starting
I received coil in mail today and was wondering what the air gap would be for it. Nowhere can I find the information for it. Thanks in advance. I appreciate the help
|
|
|
|
|
05-17-2016, 12:55 PM
|
#8 | |
|
Crazy Ole Man
Join Date: Jan 2016
Location: Owego NY
Posts: 2,758
|
Re: G16A Sputtering and starting
Quote:
|
|
|
|
|
|
05-21-2016, 08:01 AM
|
#9 |
|
Not Yet Wild
Join Date: May 2016
Location: Taber Alberta Canada
Posts: 7
|
Re: G16A Sputtering and starting
Thxs Shepard for the advice
 |
|
|
|
|
05-21-2016, 08:29 AM
|
#10 |
|
G8 Specialist
Join Date: Jun 2009
Location: Phoenix
Posts: 7,799
|
Re: G16A Sputtering and starting
Aaa, I would look at Big Block Man's signature!! Hint Hint!!
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| g16 sputtering and backfiring | Gas Yamaha | |||
| G14 Sputtering. | Gas Yamaha | |||
| 96 G16A starting problems | Gas Yamaha | |||
| G1 sputtering | Gas Yamaha | |||
| RE G1 sputtering | Gas Yamaha | |||
Linear Mode
