|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
07-11-2013, 09:02 AM
|
#1 |
|
Not Yet Wild
Join Date: Jul 2013
Posts: 12
|
Still wont go after installing new PDS
I have and 02 EZGO model D102 S/N 1475055 and I was told that the controller had gone out. The controller is a Curtis 73326G02. The symptoms were batteries are new, lights worked, radio worked, when I put it forward or reverse it would move a couple feet and stop. I upgraded to a 500 amp unit and it still does not work (at all now). the controller is wired correctly and I am once again stuck walking the street while my neighbors ride around.....any ideas on what this could be?
 |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
07-11-2013, 09:05 AM
|
#2 |
|
Techno-Nerd
 Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Still wont go after installing new PDS
Welcome to BGW!
You've got a 2002 TXT PDS. What make/model 500A controller did you install? |
|
|
|
|
07-11-2013, 09:13 AM
|
#3 |
|
Not Yet Wild
Join Date: Jul 2013
Posts: 12
|
Re: Still wont go after installing new PDS
Alltrax DCX500 PDS motor controller, ITS throttle, 36volt
|
|
|
|
|
07-11-2013, 09:59 AM
|
#4 |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Still wont go after installing new PDS
Does the green LED on the controller illuminate when the Key is ON and a direction is selected.
If so, how many times does it flash before it comes on steady? Does the solenoid click when pedal is pushed? ---------- I have some honey-do stuff to do, but I'll be back later. I suspect there was a preexisting condition that still exists.  |
|
|
|
|
07-11-2013, 10:39 AM
|
#5 | |
|
Gone Wild
Join Date: May 2013
Location: Mississippi
Posts: 301
|
Re: Still wont go after installing new PDS
Quote:
|
|
|
|
|
|
07-11-2013, 10:57 AM
|
#6 |
|
Not Yet Wild
Join Date: Jul 2013
Posts: 12
|
Re: Still wont go after installing new PDS
Solenoid clicks sometimes.......the light blinks 7 times then goes to a yellow?
|
|
|
|
|
07-11-2013, 11:06 AM
|
#7 | |
|
Gone Wild
Join Date: May 2013
Location: Mississippi
Posts: 301
|
Re: Still wont go after installing new PDS
Quote:
|
|
|
|
|
|
07-11-2013, 11:25 AM
|
#8 |
|
Getting Wild
Join Date: Aug 2010
Location: Alamogordo, NM
Posts: 144
|
Re: Still wont go after installing new PDS
I had a similar problem with my PDS, and Scotty mentioned it could be the F/R switch going bad. And that's just what it was.
|
|
|
|
|
07-11-2013, 11:52 AM
|
#9 |
|
Not Yet Wild
Join Date: Jul 2013
Posts: 12
|
Re: Still wont go after installing new PDS
Just talked to Carl at EV drives ( very nice guy ) and looks like it is programmed wrong. We are going to reprogram tonight will let everyone know how it goes. Thanks for all the help you guys ROCK!!!
|
|
|
|
|
07-11-2013, 10:17 PM
|
#10 | |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Still wont go after installing new PDS
Quote:
If it was sent to you programmed for a Club Car throttle, it probably has a Club Car Field Map also. (#6 = IQ and #8 = PD Plus) You want Field Map #4 for a PDS |
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| installing 36v/12v converter | Electric EZGO | |||
| Installing A Yamaha 350 In G2 | Bike & ATV Engine Swaps | |||
| installing a tachometer on my G1 | Gas Yamaha | |||
| installing lift kit | Gas Club Car | |||
| Installing a DCX 400 | Electric EZGO | |||
Linear Mode
