|
|
|||||||
| Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
06-08-2016, 09:27 AM
|
#11 |
|
Gone Wild
Join Date: May 2012
Location: Rio Verde, Az
Posts: 7,171
|
Re: YDRE burned controller wire
If they are clean and tight they will be ok. You can tighten them more than you think. It is also important to have the proper size lug there. Too big and it will not get as good a connection.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-08-2016, 02:51 PM
|
#12 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: YDRE burned controller wire
90269-08813
|
|
|
|
|
06-08-2016, 04:31 PM
|
#13 |
|
Not Yet Wild
 Join Date: Dec 2015
Location: Conroe, Texas
Posts: 63
|
Re: YDRE burned controller wire
One thing is for sure, I am going pay extra special attention to tightening the cables and to make sure they stay tight. All the other terminals were still tight when I removed the controller last night. Just that one got loose I guess. Question, if we assume all cables are tight correctly and have good connection and under normal driving, how hot should that motor and J9 cable get?
|
|
|
|
|
06-08-2016, 04:48 PM
|
#14 |
|
Gone Wild
Join Date: May 2012
Location: Rio Verde, Az
Posts: 7,171
|
Re: YDRE burned controller wire
Not even warm.
|
|
|
|
|
06-08-2016, 04:55 PM
|
#15 |
|
Not Yet Wild
Join Date: Mar 2015
Posts: 64
|
Re: YDRE burned controller wire
On My plowman setup i noticed the motor gets very warm also, Only problems ive had is cart will sometimes die when driving, stop and then it goes again? Checked all connections everything is tight. But motor is very hot
|
|
|
|
|
06-08-2016, 09:15 PM
|
#16 |
|
Not Yet Wild
Join Date: Dec 2015
Location: Conroe, Texas
Posts: 63
|
Re: YDRE burned controller wire
Boosted, what set up do you have and how many miles or time do you think you have on it?
|
|
|
|
|
06-08-2016, 11:23 PM
|
#17 |
|
Not Yet Wild
Join Date: Mar 2015
Posts: 64
|
Re: YDRE burned controller wire
alltrax 500 amp controller, bigger cables, solenoid, and his motor,
So my motor isnt supposed to be warm? Miles id say 50 or so |
|
|
|
|
06-14-2016, 06:41 AM
|
#18 | |
|
Gone Wild
Join Date: Jul 2015
Posts: 151
|
Re: YDRE burned controller wire
Quote:
|
|
|
|
|
|
08-09-2016, 04:36 PM
|
#19 |
|
Not Yet Wild
Join Date: Dec 2015
Location: Conroe, Texas
Posts: 63
|
Re: YDRE burned controller wire
sorry for the late response/update. Been extremely busy with work. I cannot speak highly enough of Don at Plowmans and of Alltraxx for the help they gave me during this issue I had a while back. As well as everyone on this site. I ended up getting a new controller which from all the talking with Don and Alltraxx I ended up getting a free replacement which I thought was incredibly awesome. There was not any motor damage, so I hooked up the new controller and used flat & lock washers this time, which maybe over kill but I'm not going to let what happen last time happen again. So far so good after a couple of months, and probably around 100 miles or so, no mishaps or anything. Motor still runs pretty warm but not near as hot as it did before. Thanks again to everyone here, Don and Alltraxx! If anyone has any questions just let me know.
|
|
|
|
|
08-09-2016, 04:42 PM
|
#20 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: YDRE burned controller wire
I just asked my tech rep at Alltrax about tab replacement, will let you all know what I hear.
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Burned controller -- Can you ID this IC OR Resistor? | Electric EZGO | |||
| Burned up wire off solenoid | Electric EZGO | |||
| burned green wire | Electric Club Car | |||
| burned up my controller dcx300R7 | Star and Fairplay | |||
| 91 DS wont run after controller burned up | Electric Club Car | |||
Linear Mode
