36 Volt EZ Go doesn't run....

JohnnieB · 10-03-2013, 11:22 AM

Quote:

Originally Posted by scottyb

Best to use a safe battery disconnect switch as shown in this pic. The final connection will spark and pit the terminal you connect last otherwise..... You are welcome to save, copy, or stickie my diagram.

Do you have something specifically for a Sepex motor?
Or does this series setup work on shunt wound motors also?

10-03-2013, 11:54 AM

Quote:

Originally Posted by JohnnieB

The arrow is pointing towards the rear of cart rather than the front.

i don't think so ... motor is to the right when looking from the rear to the front

JohnnieB · 10-03-2013, 12:17 PM

Quote:

Originally Posted by crash test dummy

i don't think so ... motor is to the right when looking from the rear to the front

This is the Electric EZGO forum and in an EZGO cart, the motor is behind the driver's seat.

To be honest, until your last post, I wasn't aware that Club Car motors are mounted behind the passenger seat.

I guess we both learned something new.

10-03-2013, 12:39 PM

Quote:

Originally Posted by JohnnieB

This is the Electric EZGO forum and in an EZGO cart, the motor is behind the driver's seat.

To be honest, until your last post, I wasn't aware that Club Car motors are mounted behind the passenger seat.

I guess we both learned something new.

wonder why ezgo is backward ?

i too did not know of difference
and i learn from you everyday you post

now ya'll get this member running

Rev Mejias · 10-07-2013, 08:19 AM

So I did motor test and it did run....rather slowly....but it did run. I replaced cables S1&2 The A1 &2 look good. Where to next gentleman???? By the way Crash Test....I also have a Club Car and you helped me with that one a few months back. Thanks again and Thanks in Advance. "The REV"

JohnnieB · 10-07-2013, 09:29 AM

Where to next? Performed the tests I listed in the bottom half of post#12?

Rev Mejias · 10-07-2013, 10:09 AM

If you do get FULL battery pack voltage, push the pedal to the floor.
The voltage should decrease to zero.
Okay so I have voltage across B- & A1 But when I push to the floor it does not go to Zero.

If those voltage are correct, measure between the F1 & F2 studs on motor.
With pedal on floor, you should read 2.7V.
When I measured across these there was no voltage.

scottyb · 10-07-2013, 10:32 AM

re post #21 = motor tests are different for series and sepex

Rev Mejias · 10-07-2013, 10:37 AM

See #27 Please

Rev Mejias · 10-07-2013, 10:38 AM

Is my cart an '05...Date Code E2205

10-07-2013, 08:19 AM	#25
Rev Mejias Not Yet Wild Join Date: May 2013 Location: SE TEXAS Posts: 49	Re: 36 Volt EZ Go doesn't run.... So I did motor test and it did run....rather slowly....but it did run. I replaced cables S1&2 The A1 &2 look good. Where to next gentleman???? By the way Crash Test....I also have a Club Car and you helped me with that one a few months back. Thanks again and Thanks in Advance. "The REV"

10-07-2013, 09:29 AM	#26
JohnnieB Techno-Nerd Join Date: Jun 2011 Location: West Virginia Posts: 19,654	Re: 36 Volt EZ Go doesn't run.... Where to next? Performed the tests I listed in the bottom half of post#12?

10-07-2013, 10:32 AM	#28
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,408	Re: 36 Volt EZ Go doesn't run.... re post #21 = motor tests are different for series and sepex

10-07-2013, 10:37 AM	#29
Rev Mejias Not Yet Wild Join Date: May 2013 Location: SE TEXAS Posts: 49	Re: 36 Volt EZ Go doesn't run.... See #27 Please

10-07-2013, 10:38 AM	#30
Rev Mejias Not Yet Wild Join Date: May 2013 Location: SE TEXAS Posts: 49	Re: 36 Volt EZ Go doesn't run.... Is my cart an '05...Date Code E2205

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

10-07-2013, 10:09 AM	#27
Rev Mejias Not Yet Wild Join Date: May 2013 Location: SE TEXAS Posts: 49	Re: 36 Volt EZ Go doesn't run.... If you do get FULL battery pack voltage, push the pedal to the floor. The voltage should decrease to zero. Okay so I have voltage across B- & A1 But when I push to the floor it does not go to Zero. If those voltage are correct, measure between the F1 & F2 studs on motor. With pedal on floor, you should read 2.7V. When I measured across these there was no voltage.

Similar Threads
Thread	Forum
just wondering how to put a 12 volt horn on a 36 volt ezgo cart	Electric EZGO
4-12 volt Battery Pack Run Times compared to 6 8 volt	Electric Club Car
placement when adding 2 more 6 volt batteries to 36 volt for 48 volt conversion	Electric Club Car
1990 Club Car DS 36 volt to 48 volt conversion fitting batteries question	Electric Club Car
Volt reading when Isolating 2 6v batts, is seperate volt meter needed?	Electric EZGO