Barley Moves cc Electric

kantuckian · 11-01-2019, 01:52 PM

Thanks I bet your right the owner said he bought it brand new from saylors whome i deal with yes it does have a obc and v glide am going to chec ser # again ive been known to make mistakes Thanks for helping

kantuckian · 11-01-2019, 02:01 PM

Ok like i said i make mistakes rechecked the ser# its a 99 Hopefully i can take care of it now. Thanks guys if u have any suggestions they be appreciated,

mrgolf · 11-01-2019, 02:57 PM

Now weare getting somewhere, the cart has two solenoids. Unhook negative battery cable, then take the cables on the drivers side solenoid and put both on the same big post. This will by pass the solenoid and allow the cart to run correctly.

What is happening is the driver side solenoid is bad and the cart is trying to run using the coil on the solenoid to carry the power, it is not heavy enough to so you get weak power to the motor.

Btw unhook the speed sensor or the motor braking will be very strong.

If this works like I think it will it proves the drivers side solenoid is either bad or the activation circurit is bad.

Mooncarter · 11-01-2019, 03:07 PM

Quote:

Originally Posted by mrgolf

Now weare getting somewhere, the cart has two solenoids. Unhook negative battery cable, then take the cables on the drivers side solenoid and put both on the same big post. This will by pass the solenoid and allow the cart to run correctly.

What is happening is the driver side solenoid is bad and the cart is trying to run using the coil on the solenoid to carry the power, it is not heavy enough to so you get weak power to the motor.

Btw unhook the speed sensor or the motor braking will be very strong.

If this works like I think it will it proves the drivers side solenoid is either bad or the activation circurit is bad.

Mr golf, to be clear does it matter which side he uses? And what about the small wires?

mrgolf · 11-01-2019, 04:08 PM

Makes no difference which side. If you are not going to replace the solenoid the small wires can be removed from the cart. In that case you can take the cable that comes from the controller and go to the motor with it.

Mooncarter · 11-01-2019, 04:45 PM

Quote:

Originally Posted by mrgolf

Makes no difference which side. If you are not going to replace the solenoid the small wires can be removed from the cart. In that case you can take the cable that comes from the controller and go to the motor with it.

Mooncarter · 11-01-2019, 09:20 PM

kantuckian, I did the procedure mrgolf described above on my own cart tonight. Took about 30 minutes. I left the white wire on the motor and ran it to where the other white wire went to the controller.

Cart is a LOT faster now!

kantuckian · 11-02-2019, 05:40 AM

Thanks Guys will do that and i bet it works

Mooncarter · 11-02-2019, 01:28 PM

Quote:

Originally Posted by kantuckian

Thanks Guys will do that and i bet it works

11-01-2019, 01:52 PM	#11
kantuckian Gone Wild Join Date: Dec 2010 Posts: 635	Re: Barley Moves cc Electric Thanks I bet your right the owner said he bought it brand new from saylors whome i deal with yes it does have a obc and v glide am going to chec ser # again ive been known to make mistakes Thanks for helping
kantuckian Gone Wild Join Date: Dec 2010 Posts: 635

11-01-2019, 02:01 PM	#12
kantuckian Gone Wild Join Date: Dec 2010 Posts: 635	Re: Barley Moves cc Electric Ok like i said i make mistakes rechecked the ser# its a 99 Hopefully i can take care of it now. Thanks guys if u have any suggestions they be appreciated,
kantuckian Gone Wild Join Date: Dec 2010 Posts: 635

11-01-2019, 02:57 PM	#13
mrgolf Old Sky Soldier Join Date: Dec 2011 Location: Kentucky Posts: 3,881	Re: Barley Moves cc Electric Now weare getting somewhere, the cart has two solenoids. Unhook negative battery cable, then take the cables on the drivers side solenoid and put both on the same big post. This will by pass the solenoid and allow the cart to run correctly. What is happening is the driver side solenoid is bad and the cart is trying to run using the coil on the solenoid to carry the power, it is not heavy enough to so you get weak power to the motor. Btw unhook the speed sensor or the motor braking will be very strong. If this works like I think it will it proves the drivers side solenoid is either bad or the activation circurit is bad.

11-01-2019, 04:08 PM	#15
mrgolf Old Sky Soldier Join Date: Dec 2011 Location: Kentucky Posts: 3,881	Re: Barley Moves cc Electric Makes no difference which side. If you are not going to replace the solenoid the small wires can be removed from the cart. In that case you can take the cable that comes from the controller and go to the motor with it.

11-02-2019, 05:40 AM	#18
kantuckian Gone Wild Join Date: Dec 2010 Posts: 635	Re: Barley Moves cc Electric Thanks Guys will do that and i bet it works
kantuckian Gone Wild Join Date: Dec 2010 Posts: 635

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

Similar Threads
Thread	Forum
2003 EzGo.. Barley moves	Electric EZGO
2004 club car barley moves	Electric Club Car
1993 Electric EZ Go Sometimes it moves Sometimes it don't	Electric EZGO
01 EZ GO Electric barely moves.	Electric EZGO
91 Electric CC moves in reverse only	Electric Club Car