|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
08-12-2019, 10:44 AM | #1 |
Gone Wild
Join Date: Dec 2006
Location: Pittsburgh, PA
Posts: 379
|
Jet size for G2 when running cone filter.
Does anyone off hand remember what size the main jet needs drilled out to when running a cone filter on a G2? It’s been about 15 years since I drilled my carb and just had to replace with an aftermarket and jets don’t cross from old carb to new carb. I wanna say it was .035 but can someone verify? Thanks.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-12-2019, 11:14 AM | #2 |
Gone Wild
Join Date: Jan 2017
Location: venice
Posts: 1,807
|
Re: Jet size for G2 when running cone filter.
what the heck kinda carb did you get that the jets wont swap out. Im assuming since you drilled it out you could take your old jet and see which carb bit fits in it. wish I could help more
|
08-12-2019, 11:58 AM | #3 |
Gone Wild
Join Date: Dec 2006
Location: Pittsburgh, PA
Posts: 379
|
Re: Jet size for G2 when running cone filter.
I just ordered a cheapo amazon carb for $19. Jets are smaller diameter than stock. However since posting this originally I installed new carb and it seems to run even better than when I had the old drilled carb on. So who knows. Not rly concerned with it cause I’m probably throwing a predator V twin at it over winter. Just needed to limp this anemic little single cyl the rest of the summer lol
|
08-12-2019, 12:32 PM | #4 |
Admin/Moderator
Join Date: Dec 2006
Location: Ohio
Posts: 18,055
|
Re: Jet size for G2 when running cone filter.
Hi Gary, back in the day we opened to .042 if I remember right. Just FYI that new carb is total crap! DO NOT get rid of the original carb, it can be repaired.
|
Ron
PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
08-12-2019, 01:16 PM | #5 |
Gone Wild
Join Date: Dec 2006
Location: Pittsburgh, PA
Posts: 379
|
Re: Jet size for G2 when running cone filter.
Yeah I know, like I said I don’t expect to have this motor in much longer. Finally found some time to mess around with this cart and would like to predator swap it. Those motors are **** good for the money. I will say for $19 the cart runs really good tho lol
|
08-12-2019, 04:14 PM | #6 |
Gone Wild
Join Date: Jan 2017
Location: venice
Posts: 1,807
|
Re: Jet size for G2 when running cone filter.
keep an eye on the plug for a lean condition just in case
|
08-12-2019, 07:15 PM | #7 |
Gone Wild
Join Date: Dec 2006
Location: Pittsburgh, PA
Posts: 379
|
Re: Jet size for G2 when running cone filter.
When they’re lean, they’re mean.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Oil filter bolt size | Gas EZGO | |||
What size oil filter cap wrench for new 2016 L6? | Gas EZGO | |||
18hp oil filter size??? | Clone Engine Swaps | |||
G16 running better without air filter | Gas Yamaha | |||
Which size jet to use with K N Filter? | Gas Yamaha |