|
03-22-2014, 10:12 AM
|
#1 |
|
Not Yet Wild
Join Date: Apr 2012
Location: seattle, wa
Posts: 44
|
1975 ezgo pg1 carb
does anybody know what the float setting is for the 15482g1 carb and the main jet size. any help appreciated
 . |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
03-22-2014, 11:21 AM
|
#2 |
|
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: 1975 ezgo pg1 carb
|
|
|
|
|
03-22-2014, 11:46 AM
|
#3 |
|
Not Yet Wild
Join Date: Apr 2012
Location: seattle, wa
Posts: 44
|
Re: 1975 ezgo pg1 carb
Thanks so much for your help, that manual is great help..Chuck
 |
|
|
|
|
03-22-2014, 11:48 AM
|
#4 |
|
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: 1975 ezgo pg1 carb
No problem. Go with the settings for the BV-18 carb.
|
|
|
|
|
03-24-2014, 07:25 PM
|
#5 |
|
Not Yet Wild
Join Date: Apr 2012
Location: seattle, wa
Posts: 44
|
Re: 1975 ezgo pg1 carb
Thanks again in for manual. I set the float to about .389. It started up and went about 50 feet and died. It started up and revved up until clutch kicked in and died, several times. It acts like it is not getting fuel or to much fuel. I am trying to get this thing going for my dad to go to swap meets so he can ride around. Has a hard time walking but likes to go. Thanks again for any help
|
|
|
|
|
03-25-2014, 04:28 PM
|
#6 |
|
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: 1975 ezgo pg1 carb
Did you clean the carb, and blow out the jets while you had it apart?
Is the fuel pump working? |
|
|
|
|
03-25-2014, 05:19 PM
|
#7 |
|
Not Yet Wild
Join Date: Apr 2012
Location: seattle, wa
Posts: 44
|
Re: 1975 ezgo pg1 carb
Yes, did clean and blow out carb and jets. do you know anybody who has a 15482G1 carb or some thing similiar that will work. thanks again, , it was getting fuel thanks
|
|
|
|
|
03-25-2014, 05:23 PM
|
#8 |
|
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: 1975 ezgo pg1 carb
Can you post a pic of the carb?
I think that motor has a Tillotson HL-287 or HL-279 carb. Do you see an HL number on it anywhere? |
|
|
|
|
03-26-2014, 09:01 AM
|
#9 |
|
Not Yet Wild
Join Date: Apr 2012
Location: seattle, wa
Posts: 44
|
Re: 1975 ezgo pg1 carb
no, its a mukini, ezgo told me it was a 15482g1, has choke on side and and throttle arm on top. Just like the bv18 in manual. thanks so much
|
|
|
|
|
03-26-2014, 01:01 PM
|
#10 |
|
Not Yet Wild
Join Date: Apr 2012
Location: seattle, wa
Posts: 44
|
Re: 1975 ezgo pg1 carb
I put car on jack stands and fired up engine, ran good as it revved up.air screw 1 1/2 turn main jet was 114 could not find a 92.5, solder jet and drilled out to 105, smallest bit I had. It bogged a bit before it started to rev up on high rpm. Took off jack stands and tried it. It started to rev up and clutch kicked in tires swelled and died. It did this repeatedly. Is this carburation or what. I am at wits end on this. So close yet so far away
|
|
|
|
 |
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| 1975 ezgo pg1 carb | Gas EZGO | |||
| 1975 ezgo | Gas EZGO | |||
| 1975 ezgo gas | Gas EZGO | |||
| 1975 ezgo gas | Gas EZGO | |||
| 1975 ezgo 2stroke | Gas EZGO | |||
Linear Mode
