02-14-2020, 04:51 PM | #21 |
Nincompoop village idiot
Join Date: Apr 2018
Location: Michigan
Posts: 9,682
|
Re: Robin EH29C
Make sure the cam lobes are pointing down when you adjust. You'll have to rotate the engine over once to do the 2and cylinder.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-14-2020, 05:12 PM | #22 |
Not Yet Wild
Join Date: Mar 2018
Posts: 29
|
Re: Robin EH29C
I always forget about good ol you tube. Hittin that now. Let yall know later!
Sent from my SM-N950U using Tapatalk |
02-14-2020, 06:59 PM | #23 |
Vintage tech
Join Date: Sep 2009
Location: South
Posts: 3,216
|
Re: Robin EH29C
The picture I included in post 17 shows how your lobe should be pointing ( down ) . 10 mm socket and remove the valve cover. Then just take a 10mm wrench and screwdriver.
You will know if these intakes are pulled into the head as soon as you remove the valve cover. As Cartmaster said, count the amount of thread showing on the two middle valves compared to the other two. |
02-14-2020, 07:44 PM | #24 |
Not Yet Wild
Join Date: Mar 2018
Posts: 29
|
Re: Robin EH29C
Thanks on my way home to check this out. First I'll stop at auto store to pick up oil and plugs. Do I use synthetic? 10w-30 or just 30w? Also are plugs pre gapped? What should gap be?
Sent from my SM-N950U using Tapatalk |
02-14-2020, 10:44 PM | #25 |
Vintage tech
Join Date: Sep 2009
Location: South
Posts: 3,216
|
Re: Robin EH29C
I always use regular 10w30. Plugs gap at 030 . I would use the NGK BP4ES plugs and unless someone dropped them they are pre-set
|
02-14-2020, 11:16 PM | #26 |
Not Yet Wild
Join Date: Mar 2018
Posts: 29
|
Re: Robin EH29C
Ok from top to bottom...... top is .004 and this one won't adjust. I loosened nut and turned screw down and still no gap.
Sent from my SM-N950U using Tapatalk |
02-14-2020, 11:30 PM | #27 |
Not Yet Wild
Join Date: Mar 2018
Posts: 29
|
Re: Robin EH29C
Update...... almost have to run screw to very top to fit .004
Sent from my SM-N950U using Tapatalk |
02-15-2020, 12:07 AM | #28 |
Not Yet Wild
Join Date: Mar 2018
Posts: 29
|
Re: Robin EH29C
Here is the pic of that valve adjusted. I checked compression and now have 180psi on both cylinders. Is this valve going bad?
Sent from my SM-N950U using Tapatalk |
02-15-2020, 12:10 AM | #29 |
Not Yet Wild
Join Date: Mar 2018
Posts: 29
|
Re: Robin EH29C
Trig.... I actually forgot to check gap according to picture you sent me. I followed a you tube video that showed to check under set screw. Am I good either way?
Sent from my SM-N950U using Tapatalk |
02-15-2020, 12:20 AM | #30 |
Gone Wild
Join Date: Feb 2010
Location: Homosassa, FL
Posts: 415
|
Re: Robin EH29C
Valves are getting wore out with that much thread showing
It’s a common problem with these engines after being neglected Just monitor them and run them drain all the oil out of the motor and fill it up with 1.5qt like mentioned before I have a lifted cart and have to take my front wheels off and jack the back end up to get all the oil out of mine But should run good after that |
|
|
Similar Threads | ||||
Thread | Forum | |||
Robin eh29c camshaft | Gas EZGO | |||
Robin EH29C Parts | Golf Carts and Parts | |||
Robin eh29c 295cc | Gas EZGO | |||
Robin eh29c | Gas EZGO | |||
Smoking EH29C Robin | Gas EZGO |