|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
11-27-2021, 06:15 PM | #11 |
Gone Wild
Join Date: Jan 2011
Location: mascoutah,il
Posts: 387
|
Re: Hunting Cart down
OK I replaced the contactor with Scotties SW202 unit I still have the same issue I tried to upload some videos but they will not load?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-28-2021, 09:27 AM | #12 |
Gone Wild
Join Date: Oct 2012
Location: Southwestern Pa.
Posts: 6,215
|
Re: Hunting Cart down
Just posted to follow
|
11-28-2021, 06:37 PM | #13 |
Gone Wild
Join Date: Jan 2011
Location: mascoutah,il
Posts: 387
|
Re: Hunting Cart down
I do NOT know how the contactor actually works but here are some of the reading I have,
In "R" 51.2V on S1 out of the Contactor In "F"F 1.02V on S2 out of the Contactor I checked the power to the Contactor from the switch and have the same voltage on both sides when in forward and reverse. 1.08V It seems to me that the contactor is not opening in forward to allow voltage to run the motor?? I had the same readings on the old and new contactor. What to look at next? |
11-29-2021, 08:29 PM | #14 |
Gone Wild
Join Date: Jan 2011
Location: mascoutah,il
Posts: 387
|
Re: Hunting Cart down
So to recap what I have:
SPM controller smoked- replaced with SP48400 Cart will only go in Reverse,Only shudders in Forward ScottyB and I have communicated through 65 emails. Replaced Contactor with SW202 and have the same result? I will attach the controller settings and I hope someone can compare to their settings.I have downloaded from Altrax the wiring diagram for SP controller and Rev Contactor and have noticed that it is different than the diagram that came with ScottyB part? If ANYONE has any ideas of what to check that would GREAT! https://buggiesgonewild.com/attachme...1&d=1638235141 https://buggiesgonewild.com/attachme...1&d=1638235141 |
11-30-2021, 10:49 AM | #15 |
Gone Wild
Join Date: Jul 2018
Location: Ramer, AL
Posts: 1,450
|
Re: Hunting Cart down
Is it possible that you have a corroded cable/connection on the forward side? Swap cables and see if the problem moves with the cable.
|
11-30-2021, 10:54 AM | #16 |
Gone Wild
Join Date: Jan 2011
Location: mascoutah,il
Posts: 387
|
Re: Hunting Cart down
If I swap S1 and S2 the cart will go OK in forward but shutters in Reverse. The S2 cable is clean and test good.
|
11-30-2021, 11:05 AM | #17 |
Gone Wild
Join Date: Jul 2018
Location: Ramer, AL
Posts: 1,450
|
Re: Hunting Cart down
All your connections look corroded. Order new cables (cheap) and I would start from battery negative, clean/replace cables, working your way back to battery positive.
https://www.batterycablesusa.com/2-g...battery-cables |
11-30-2021, 11:14 AM | #18 |
Gone Wild
Join Date: Oct 2012
Location: Southwestern Pa.
Posts: 6,215
|
Re: Hunting Cart down
Here are my settings.
On your throttle settings set YOUR TORQUE CURVE back to "STANDARD" |
11-30-2021, 12:11 PM | #19 |
Gone Wild
Join Date: Jan 2011
Location: mascoutah,il
Posts: 387
|
Re: Hunting Cart down
OK,Thanks
|
11-30-2021, 01:03 PM | #20 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Hunting Cart down
If the symptoms are runs okay in R and shudders in F and when the S1/S2 cables are swapped it runs okay in F and shudders in R, than the problem is either a poor NO contact on the solenoid energized when F is selected or poor NC connection on the solenoid not energized when F is selected. (Or there is a slight chance the SRs reverse speed slider is set too low)
Much to my dismay, I don't have schematics of a reversing contactor showing the actual current paths through the NO and NC contacts when F is selected or when R is selected, but a reversing contactor is simply two SPDT solenoids whose contacts are wired so the polarity of S1 and S2 depends on which of the two solenoids is energized. The closest thing I have is from the SW202 datasheet, but is has the direction of amp flow through the armature windings being reversed rather than the stator windings like EZGO does it. Also both solenoids are de-energized while in actual operation, one is energized and the other isn't. ------------ If I had this cart in front of me, I'd measure the voltage between the two coil terminals on each of the solenoids in both F and R. The coils are supposed to be being energized with FULL battery pack voltage, if on is getting less than FULL battery pack voltage, it may not be closing the NO contacts properly. I'd also set the SR's reverse speed slider to 100% so the output voltage in F or R would be the same. Then the voltage between m- and B+ ought to be the same when in F or R with the pedal pressed the same. From the symptoms, the voltage is going to be lower in F than R, and you ought to be able the follow the amps through the NO and NC contacts to find the missing voltage. |
|
|
Similar Threads | ||||
Thread | Forum | |||
My g1 hunting cart | Gas Yamaha | |||
RXV for Hunting cart ??? | Electric EZGO | |||
hunting cart | Electric Club Car | |||
What a Hunting Cart needs ? | Electric EZGO | |||
Help with hunting cart | Lifted Golf Carts |