|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
11-26-2014, 05:47 PM | #1 |
Not Yet Wild
Join Date: Sep 2014
Location: Loris SC
Posts: 15
|
Aftermarket Rear Fender Eztentions
I just received new rear fender extensions for my 88 Marathon . I can tell already they are not a good fit . I thought I caught a mention of this on another thread , tried searching for it with no luck. Have any of you guys installed these extensions and what did you do to fit them . I was thinking of heating them to fit . Any good ideas ? .Don
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-26-2014, 05:50 PM | #2 |
Gone Wild
Join Date: Oct 2009
Location: Alva Fla
Posts: 608
|
Re: Aftermarket Rear Fender Eztentions
Post a few pics so we can see what the issue is.
|
11-26-2014, 06:01 PM | #3 |
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: Aftermarket Rear Fender Eztentions
|
11-26-2014, 06:32 PM | #4 |
Not Yet Wild
Join Date: Sep 2014
Location: Loris SC
Posts: 15
|
Re: Aftermarket Rear Fender Eztentions
Here are some pictures 230 is the extension bolted at the bottom , you can see the ext. looks like it was made for a fender that is cut off at a 90 degree angle instead of an angle . 233 and 232 the ext. is on the fender but does not fit the lower leg of the body . Don
|
11-26-2014, 06:43 PM | #5 |
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: Aftermarket Rear Fender Eztentions
They actually look pretty good to me. The biggest issue I had was getting all the bolts in.
Install the bolts first, just finger tight, then install the lower plate and rivets. The plastic will twist around to line up. Then move the top part around if you have to and tighten the bolts |
11-27-2014, 12:11 AM | #6 |
Gone Wild
Join Date: Feb 2011
Posts: 1,515
|
Re: Aftermarket Rear Fender Eztentions
You do have the metal plates right !!! that will make them form to the fender when bolted down. Just thinking LOU
|
11-27-2014, 10:19 PM | #7 |
Not Yet Wild
Join Date: Sep 2014
Location: Loris SC
Posts: 15
|
Re: Aftermarket Rear Fender Eztentions
Thanks guys , yes I do have the plates . The weather down here is supposed to warm up Monday and I will get back to it . Thank again . Don
|
12-03-2014, 08:09 PM | #8 |
Not Yet Wild
Join Date: Sep 2014
Location: Loris SC
Posts: 15
|
Re: Aftermarket Rear Fender Extentions
I got some more pictures of these aftermarket exts. #238 I took a pencil and centered the middle hole . #236 shows how it is too wide for the plate about 3/8" on both sides . #234 I sled the plate to one side. #235 the same thing . When I hold the top of the ext. to the fender it over laps the fender about a 1/4" on ether side . I attached the two lower bolts , it had rivets originally , and it pulls away from the fender and when I bend it around to fit it is to low on the outside corner. I guess I will try to heat them into place and re drill the holes . If any other ideas Please chime in . Don
|
12-04-2014, 11:29 AM | #9 |
Hammer Down !!!!
Join Date: Jun 2010
Location: Lake Geneva, WI
Posts: 2,681
|
Re: Aftermarket Rear Fender Eztentions
heat is always your friend with almost all the Marathon trim pieces, cowl cap, fender caps, etc - they almost never want to drop right into place. Take your time, gentle heat, and You should be fine
|
12-05-2014, 03:11 PM | #10 |
Not Yet Wild
Join Date: Sep 2014
Location: Loris SC
Posts: 15
|
Re: Aftermarket Rear Fender Eztentions
Thanks Guys , I got them on , don't like the fit . I guess I can live with it . Don
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Need rear hitch for ST 4x4 used or aftermarket | Gas EZGO | |||
WTB 92 EZ GO rear fender | Golf Carts and Parts | |||
Any alternative or aftermarket Fender Flares? | Gas EZGO | |||
G9 Rear fender replacement. | Design Center | |||
Clutch for Aftermarket Rear End | Big Block Talk! |