|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
04-11-2015, 09:06 AM | #11 |
Getting Wild
Join Date: Apr 2014
Location: Florida
Posts: 129
|
Re: G21 help.
Ok so I just retested I am getting just under 140 cold and fresh. 150ish with oil
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-11-2015, 09:10 AM | #12 |
Getting Wild
Join Date: Apr 2014
Location: Florida
Posts: 129
|
Re: G21 help.
Ok so I am getting 140 compression and 150 with a little oil in the cylinder. But attached is what assume should be the weight. All the rollers are flat and I may as well change the rollers and weights. But online hat totals to over 300$ lucky I got a buddy that's a yamie dealer and I can get complete primary clutch for under the 3 mark :) should I just replace the entire thing
|
04-11-2015, 09:20 AM | #13 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: G21 help.
Can you post a picture of the clutch?
|
04-11-2015, 09:38 AM | #14 |
Getting Wild
Join Date: Apr 2014
Location: Florida
Posts: 129
|
Re: G21 help.
Here is he clutch
|
04-11-2015, 09:50 AM | #15 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
Re: G21 help.
If it's missing parts and is that messed up, I would just go ahead and get a new OEM clutch and be done with it.
Aftermarket clutches from China aren't that great. |
04-11-2015, 09:52 AM | #16 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: G21 help.
Why the heck is the weight missing Take the belt off, grab the clutch and move it side to side to see if the bushings in the sliding sheave are worn. Also check the face (were the belt rides) to see if the aluminum is worn. Is the place the missing weight attatches broken? If all checks good, I'll send you a good used weight/bolt and plastic washers. If doesn't check out good...get the whole new OEM clutch assy.
|
04-11-2015, 07:28 PM | #17 |
Getting Wild
Join Date: Apr 2014
Location: Florida
Posts: 129
|
Re: G21 help.
Thanks smallblock i called my local yamaha dealer that i am good with for boat parts here in miami and i order new....COMPLETE Clutch Assy. New Throttle to Governor Cable (opened the ACCEL plate and found a make shift cable tie wrapped to accel ....OMG) New Governor to Carb cable new carb gaskets and air cleaner gaskets......hopefully swap this out next week and boom goes the dynamite!!! on another note..Are there any aftermarket mufflers for the 351 that will quite it down a bit???
P.S. After i had it all apart and just ran the cart with my hand on the governor she ran well....Seemed to get a good amount of speed so i am thinking all will be well once i get these parts correct i can't believe people rig things like this........ |
04-11-2015, 08:04 PM | #18 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G21 help.
Glad to see you are going to fix it right! I cant stand it when people 'rig 'em up with junk, then get upset when you tell them that their rig-job is why it does not do what they expect.
|
04-11-2015, 08:13 PM | #19 |
Getting Wild
Join Date: Apr 2014
Location: Florida
Posts: 129
|
Re: G21 help.
Ha.....me too. Some people just don't thin. thanks CG I will post Picts as I go along.
|