|
Big Block Talk! Everything about swapping a big block engine into your cart! |
|
Thread Tools | Display Modes |
05-14-2020, 09:33 AM | #1 |
Gone Wild
Join Date: Jun 2011
Location: Kingston Springs Tn.
Posts: 874
|
Drop cradle bracket G14
Just put a 6 in lift in my g14 now engine is at an extreme angle Vegas has a drop bracket for a g8/9 listed anyone know if that will fit can’t get any sense out of Ivan
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-14-2020, 01:47 PM | #2 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: Drop cradle bracket G14
The G14 was a 1 1/2 year car. If you look at the "front" pivot point were the swing arm and main frame join, you'll see it has a bolt going thru horizontal. I would find out what size the thru bolt is and buy some heim joints simular to what Vegas Carts do for there EZgo drop brackets. Good luck
|
05-14-2020, 05:13 PM | #3 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,442
|
Re: Drop cradle bracket G14
|
05-14-2020, 05:27 PM | #4 |
Gone Wild
Join Date: Jun 2011
Location: Kingston Springs Tn.
Posts: 874
|
Re: Drop cradle bracket G14
Front link
|
05-14-2020, 06:14 PM | #5 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,442
|
Re: Drop cradle bracket G14
So it just has a single connection in the front?
I know you're swing arm is different than a G9, but check out this one I did. Look at post 4, 5, and 6. I cut the front swing arm frame and dropped it. Welded in some 3/16 steel plates to connect them. It worked great. Not sure if you could do the same thing with yours, but maybe similar. https://www.buggiesgonewild.com/showthread.php?t=122992 |
05-14-2020, 06:19 PM | #6 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,647
|
Re: Drop cradle bracket G14
Single pivot point at the front and a G 16 panhard bar at the rear.
|
05-14-2020, 06:26 PM | #7 |
Gone Wild
Join Date: Jun 2011
Location: Kingston Springs Tn.
Posts: 874
|
Re: Drop cradle bracket G14
Yep single mount in front guess im gonna have to fab something or
Heim joints were suggested above now my question is Will it hurt to run it at an angle till I can figure something out ? |
05-14-2020, 06:27 PM | #8 | |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,647
|
Re: Drop cradle bracket G14
Quote:
|
|
05-14-2020, 06:51 PM | #9 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,442
|
Re: Drop cradle bracket G14
Here's Vegas Cart's guide to the different swing arm/ cradle designs for comparison. Maybe you could use a different design swing arm/cradle? Or maybe this will give you an idea from looking at other cradles.
Another way is to drop the engine cradle portion. Keep the outer frame the same, but just build an interior frame the engine sits on and drop it down in the front. Just an idea. https://vegascarts.com/blogs/faq/yam...identification |
05-14-2020, 06:51 PM | #10 |
Gone Wild
Join Date: Jun 2011
Location: Kingston Springs Tn.
Posts: 874
|
Re: Drop cradle bracket G14
I suppose that’s the factory set up
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Yamaha G16 cradle drop | Lifted Golf Carts | |||
Dropping engine cradle mount on lifted G22a - Bracket? | Gas Yamaha | |||
Need some ideas for a leveling/drop bracket for g19 Yamaha | Lifted Golf Carts | |||
Track bar drop bracket | Gas Yamaha | |||
anybody selling Yamaha motor Drop bracket? | Big Block Talk! |